Publicité
Les langues disponibles
Les langues disponibles
FAILURE TO OBSERVE THESE WARNINGS COULD RE SULT IN IN JU RY.
THIS
INSTRUCTION
CONTAINS IMPORTANT SAFETY
INFORMATION.
READ THIS INSTRUCTION MANUAL CAREFULLY
AND UNDERSTAND ALL INFORMATION BEFORE
OPERATING THIS TOOL.
• Read and understand all instructions.
Failure to follow all instructions listed below,
may result in electric shock, fire, explosion
and/or serious personal injury. It is the
responsibility of the owner to make sure all
personnel read this manual prior to using
the device. It is also the responsibility of the
device owner to keep this manual intact and
in a convenient location for all to see and read.
If the manual or product labels are lost or not
legible, contact NAPA for replacements. If the
operator is not fluent in English, the product
and safety instructions shall be read and
discussed with the operator in the operator's
native language by the purchaser/owner or
his designee, making sure that the operator
comprehends its contents.
• Always operate, inspect and maintain this
tool in accordance with American National
Standards Institute Safety Code of Portable
Air Tools (ANSI B186.1) and any other
applicable safety codes and regulations.
• For safety, top performance and
maximum durability of parts,
operate this tool at 90 psig; 6.2
bar max air pressure with 3/8"
diameter air supply hose.
• Always wear impact resistant
eye,face & hand protection
(Users & Bystanders) when
operating
or
maintenance on this tool
• High sound levels can cause
permanent hearing loss. Always
use hearing protection as
recommended by your employer
an OSHA regulations while using
this tool (users and bystanders).
• Keep the tool in efficient operating
condition.
• Operators and maintenance personnel
must be physically able to handle the bulk,
weight and power of this tool.
• Air under pressure can cause
severe injury. Never direct air
at yourself or others. Always turn
off the air supply, drain hose
of air pressure and detach tool
from air supply before installing,
removing or adjusting any
accessory on this tool, or before
performing any maintenance on
this tool Failure to do so could
6-1156
MANUAL
result in injury. Whip hoses can cause serious
injury. Always check for damaged, frayed or loose
hoses and fittings, and replace immediately. Do
not use quick detach couplings at tool. See
instructions for correct set-up.
• Keep tool out of reach of children.
• Air powered tools can vibrate
in use. Vibration, repetitive motions
or uncomfortable positions over
extended periods of time may be harmful to
your hands and arms. Discontinue use of tool if
discomfort, tingling feeling or pain occurs. Seek
medical advice before resuming use.
• Slipping, tripping and or falling
while operating air tools can be a
major cause of serious injury or
death. Be aware of excess hose left on the
walking or work surface.
• Keep body working stance balanced and
| firm. Do not overreach when operating the
tool.
• Do not point or indulge in any horseplay with
this tool.
• Anticipate and be alert for sudden changes
in motion during start up and operation of any
power tool.
• Do not carry tool by the hose.
Protect the hose from sharp objects
and heat.
• Tool shaft may con tin ue to ro tate brief ly af ter
throt tle is re leased. Avoid di rect con tact
with ac ces so ries dur ing and af ter use. Gloves will
re duce the risk of cuts or burns.
• Keep away from rotating end
of tool. Do not wear jewelry or
performing
loose clothing. Secure long hair.
Scalping can occur if hair is not kept
away from tool and accessories. Choking
can occur if neckwear is no kept away from
tool and accessories.
• Correct cut-off wheel mounting is necessary
to prevent injury from broken wheels. Do not
use chipped or cracked cut-off wheels. Cut
off wheels should be a free fit on the spindle
to prevent stress at the hole. Use only wheel
collars that come with the tool for mounting
the cut-off wheel. Flat washers or other
adapters may over stress the wheel. Tighten
the wheel on the spindle to prevent spin off
when the tool is turned off.
• When using the cut-off tool, be careful not
to exert excessive force. Too much force
could be hazardous if it causes the tool spindle
to bend or break. The burning of the work
piece or excessive speed reduction indicates
too much force being applied. Start the tool
off the work, set it down on the work evenly
and move in the direction desired to make
the cut. When finished cutting, lift off the
WARNING
2
work before stopping the motor.
• Never operate this tool without required
disc cover/guard in place.
• RPM of the accessory must
exceed
tool
RPM
RPM
RPM
accessories rated at 21,000
rpm or higher.
• Use accessories recommended by NAPA
tools.
• Do not lu bri cate tools with
flam ma ble or vol a tile liq uids such
as ker o sene, die sel or jet fuel.
• This tool is not insulated against
electric shock.
• This tool must not be used in
explosive atmospheres.
• Servicing and repairs should only
be made by an authorized service
center.
• Do not force tool beyond its rated capacity.
• Do not remove any labels. Replace
damaged labels.
• Do not lock, tape or wire the "on/off"
safety lever in the "on" position, as the
lever must be free to return to the "off"
position when released.
• Failure to heed these warnings may reusult
in personal injury and/or property damage.
WARNING: This product can
expose
you
to
including
nickel
known to the State of
C a l i f o r n i a
to cause cancer and birth defects or
other reproductive harm.
information
go to www.P65Warnings.
ca.gov.
rpm.
Us
chemicals
which
is
For more
Rev. 05/22/23
Publicité
