Fahrenheit 77007717 Guide D'utilisation page 2

GUIDE D'UTILISATION /
USER GUIDE
H BURNER
Q DUAL
77007717 - 77007718
CAUTION
Before beginning installation, turn the gas off at the
tank and disconnect any electric current.
T LS REQUIRED
Flat head screwdriver, adjustable wrench or pliers.
INSTA ATION
1. Leg height adjustment
a) Remove cooking grid, rocks and grate from
your BBQ. If your BBQ includes an ignitor,
remove the electrode wire terminal from the
ignitor. Remove the burner from the BBQ.
b) Install the feet on the new burner:
• Thread the feet into the holes provided.
• Adjust foot height to duplicate the old burner's
height by turning the feet in or out.
• Insert the burner into the BBQ casting to be
sure the feet do not fall through openings in
bo om of casting. If feet do fall through,
simply turn a foot away from the hole.
2. Venturi installation (FIGURE A)
a) Place the new burner on a flat surface with the
venturi holes facing upward.
b) Place gaskets and venturis over proper
mounting holes in burner.
N° Description
1 Hanger bolts
2 Burner base
3 Security springs
4 Lock screws #8 X ¼"
5 Venturis
6 Gaskets
7 Burner securing stud
Metal screws #10 X ⁄ ₈ "
8
9 Cover plates
10 Adjustment bar
11 Hex nuts #10
12 Adjustment bars
USER GUIDE
c) Secure venturis,
applicable) and hold down bracket bolt to
burner by using four self-tapping screws.
A ach the burner hold down bracket bolt on the
opposite side of tubes from the ignitor bracket.
Do not overtighten screws.
d) Place gaskets and cover plates over remaining
openings in burner and bolt it to the burner
using four self-tapping screws. Do not
overtighten screws.
e) Venturis are both expanding and flexible so they
may be custom fit to your BBQ. Place the old and
new burners next to each other and extend and
bend the flexible tubing on new venturis like the
old burner. Hold venturis securely while
bending to avoid loosening connection or
damaging gaskets.
f) Turn the new burner assembly over so the
venturis point downward and lower burner into
your BBQ. The burner hold down bracket bolt
will be protruding downward and should be
maneuvered through any of the openings in
bo om of grill casting. Be careful to fit venturis
properly over gas orifices on the BBQ
(FIGURE B).
g) With the burner firmly seated in the center of
grill casting, place bracket over bracket bolt
and thread wing nut onto bolt. Hand tighten
wingnut to secure burner in proper position.
Quantity
4
FIGURE A
1
2 10
2
2
7
4
8
1
8
12
2
1
9
2
ignitor bracket (when
11
5
4
3
1
9
2
6
h) Safety feature: Fix one locking screw on each
end of venturi tube. Tightly wrap one end of
each steel wire around the locking screws on
each venturi tube. Tightly wrap the other end of
each steel wire around the control valve body.
The safety wires should be tight to act as an
additional feature to keep the burner in place
(FIGURE C).
i) Test the burner before installing grates and lava
rocks. A blue cone-shaped flame should burn
evenly around the burner within thirty
seconds after ignition. The venturi tubes are
manufactured so that no air adjustment
is required.
CAUTION
Adjustment of burner is the most critical step of the
installation. Wrong mating of venturi tubes over
gas orifices will result in malfunction of this unit.
Failure to follow these instructions may result in
property damage and injury.
FIGURE B
GASKET
FLEXIBLE
VENTURI TUBE
FIGURE C
SAFETY WIRES
CONTROLE VALVE BODY
NOVELCA, 5355, BOUL. DES GRADINS, QUÉBEC (QUÉBEC) CANADA G2J 1C8
GAS ORIFICE
LOCKING SCREWS
F2312