Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
IMPORTANT–Please Read and Follow!
•
Please read all instructions thoroughly before installing the Built-In Microwave Hood. Two people are
recommended to install this product.
•
If a new electrical outlet is required, its installation should be completed by a qualified electrician before the
Built-In Microwave Hood is installed. See ELECTRICAL GROUNDING INSTRUCTIONS on page 2.
Unpacking and Examining
Your Oven
Open the bottom of the carton, bend the carton flaps
back and tilt the oven over to rest on plastic foam pad.
Lift carton off oven and remove all packing materials,
Wall and Top Cabinet Template, Turntable, and Turntable
Suppor t. SAVE THE CARTON AS IT MAY MAKE
INSTALLATION EASIER.
•
Remove the feature sticker from the outside of the
door, if there is one.
•
DO NOT REMOVE THE WAVEGUIDE COVER, which
is located on the right side wall of the oven cavity.
Check to see that there is a Wall TEMPLATE and Top
CABINET Template. Read enclosures and SAVE the
Use and Care manual.
Check the oven for any damage, such as misaligned or
bent door, damaged door seals and sealing surfaces,
broken or loose door hinges and latches and dents inside
the cavity or on the door. If there is any damage, do
not operate the oven and contact your dealer or Viking
AUTHORIZED SERVICER.
All manuals and user guides at all-guides.com
Designer Built-In Microwave Hood
Viking Installation Guide
1 Mounting Space
This Built-in Microwave Hood requires a mounting space
on a wall as shown in Figure 1. It is designed to be used
under standard 12" wall cabinets.
1
12"
15.5"
At least 2"
Backguard
Greenwood, Mississippi 38930 USA
30"
30" or more
from cooking
surface
66" or more
from floor
111 Front Street
Publicité
Manuels Connexes pour Viking Range Corporation DMOR200SS
Sommaire des Matières pour Viking Range Corporation DMOR200SS
- Page 1 All manuals and user guides at all-guides.com Viking Installation Guide IMPORTANT–Please Read and Follow! • Please read all instructions thoroughly before installing the Built-In Microwave Hood. Two people are recommended to install this product. • If a new electrical outlet is required, its installation should be completed by a qualified electrician before the Built-In Microwave Hood is installed.
- Page 2 All manuals and user guides at all-guides.com 2 Wall Construction ElEctrical rEquirEmEnts This Built-in Microwave Hood should be mounted against and supported by a flat vertical wall. The wall must be The oven is equipped with a 3-prong grounding plug. DO flat for proper installation.
- Page 3 All manuals and user guides at all-guides.com 4 Hood Exhaust Duct 5 Tools Recommended for Installation When the hood is vented to the outside, a hood exhaust • Phillips Screwdriver • Pencil duct is required. All ductwork must be metal; absolutely •...
- Page 4 All manuals and user guides at all-guides.com 7 Preparation of the Oven Separate mounting plate from oven by removing two (B) Horizontal Exhaust: Outside screws. See illustration below. Save these screws for use Ventilation in section Mounting Oven to Wall, figure /. Mounting Plate 1) HORIZONTAL EXHAUST: Remove 2 screws from back...
- Page 5 All manuals and user guides at all-guides.com 8 Ventilation System (Preparing Oven for Installation) Save fan cover bracket for future instructions. 4) HORIZONTAL EXHAUST: Put the wire back into the 2) VERTICAL EXHAUST: Lift Hood Fan Unit carefully and cavity. The Fan Cover Bracket and Exhaust Damper slip wires out of cavity.
- Page 6 All manuals and user guides at all-guides.com 8 Ventilation System (Preparing Oven for Installation) Mounting Scale Plate Scale Plates Mounting Plate 4) VERTICAL EXHAUST: Attach the Fan Cover Bracket to unit with the 2 screws from back edge and 3 screws from the top center of the Fan Cover Bracket, which were removed OVEN INSTALLATION: The Scale Plates are used to help in Step 1.
- Page 7 All manuals and user guides at all-guides.com 9 Oven Installation 10 Mounting Oven to the Wall Utilization of the carton may make installation easier. Space more than wall thickness Wall Top Side Cutting Line 2) MOUNTING PLATE: Position the Mounting Plate with the Toggle Bolts attached at the wall location and insert Toggle Nuts and Bolts through the holes in the wall with 1) MOUNTING OVEN TO THE WALL: Place carton upside...
- Page 8 Checklist for Installation • Make sure the unit has been installed according to all of the Installation Instructions and the Wall and Top Cabinet Templates. Viking Range Corporation • Plug in the power cord. 111 Front Street Greenwood, Mississippi 38930 USA •...
- Page 9 All manuals and user guides at all-guides.com Viking Instructions d’installation IMPORTANT–S’il vous plaît lisez et suivez! • Veuillez lire attentivement toutes les instructions avant d’installer le système de Micro-onde intégrée. Nous recommandons que deux personnes collaborent à l’installation de cet appareil. •...
- Page 10 All manuals and user guides at all-guides.com 2 Construction du Mur installatiOn ÉlEctriquE Le Micro-onde intégrée doit être monté sur et supporté par un mur vertical plat. Pour une installation correcte, le Le four est équipé d’une fiche de terre à 3 broches. IL mur doit être plat.
- Page 11 All manuals and user guides at all-guides.com 4 Conduit d’évacuation à la 5 Outils recommandés pour Hotte l’installation Pour une hotte avec évacuation à l’air libre, il faut installer • Tournevis Phillips • Crayon un conduit d’évacuation à la hotte. Tous les conduits •...
- Page 12 All manuals and user guides at all-guides.com 7 Préparation du four Détachez la plaque de montage du four en retirant deux (B) échappement Horizontal : vis.Voir l’illustration ci-dessous. Conservez ces vis pour Ventilation extérieure les utiliser à la section MONTAGE MURAL DU FOUR, étape /.
- Page 13 All manuals and user guides at all-guides.com 8 Système de Ventilation (Préparation du four pour l’installation) 3) éCHAPPEMENT HORIZONTAL: Faites pivoter l’unité de ventilation de hotte de 180° de façon à ce que les ouvertures de pales de ventilateur soient orientées vers l’arrière du four. Voir le Schéma 7 (A).Faites attention de ne pas pincer le fil et l’unité...
- Page 14 All manuals and user guides at all-guides.com 8 Système de Ventilation 9 Installation du Four (Préparation du four pour l’installation) CE FOUR NE PEUT PAS êTRE INSTALLÉ CORRECTEMENT SANS SE REPORTER AUX INSTRUCTIONS DE MONTAGE PORTÉES SUR LES GABARITS DE COFFRET DE MONTAGE MURAL ET AU PLAFOND.
- Page 15 All manuals and user guides at all-guides.com 10 Montage Mural du Four L’utilisation du carton peut faciliter l’installation. Deje espacio superior al espesor de pared Pared Côté Ligne de Supérieur découpage 2) PLAqUE DE MONTAGE: Positionnez la plaque de montage avec les boulons à ailettes sur l’emplacement 1) MONTAGE MURAL DU FOUR: Placez le carton à...
- Page 16 à graisse 9. Pense-bête pour l’installation • Assurez-vous que l’appareil a été installé en suivant toutes les instructions et en utilisant le gabarit mural et de plafond. Viking Range Corporation • Branchez le cordon d’alimentation secteur. 111 Front Street •...
- Page 17 All manuals and user guides at all-guides.com Viking Instrucciones de Instalación IMPORTANTE–Por favor lea y siga! • Por favor lea cuidadosamente todas las instrucciones antes de instalar el Diseñador Microondas para Emmpotrado. Se recomiendan dos personas para instalar este producto. •...
- Page 18 All manuals and user guides at all-guides.com 2 Construcción de la Pared rEquErimiEntOs ElÉctricOs Este Diseñador Microondas para Emmpotrado debe contar y soportarse en una pared vertical plana. La pared El horno está equipado con un enchufe de conexión debe ser plana para instalación apropiada. Si la pared a tierra, de tres patas.
- Page 19 All manuals and user guides at all-guides.com 4 Ducto de Escape de 5 Herramientas Recomendadas Campana Extractora para la Instalación Cuando la campana extractora tiene escape hacia el • Atornillador Phillips • Cinta exterior, se requiere un ducto de escape de campana. •...
- Page 20 All manuals and user guides at all-guides.com 7 Preparación del horno (B) Escape Horizontal: Separe la placa de montaje del horno retirando dos Extracción hacia tornillos. Véase la Figura a continuación. Guarde estos el exterior tornillos para usarlos en la sección MONTAJE DEL HORNO EN LA PARED, paso /.
- Page 21 All manuals and user guides at all-guides.com 8 Sistema de Escape (Preparación del horno para Instalación) (C) Escape Vertical: Extracciòn hacia el (A) Gire 180˚ exterior 1) ESCAPE VERTICAL: Remueva y guarde los 2 tornillos del 3) ESCAPE HORIZONTAL: Rote 180° la Unidad de Ventilador borde trasero y los 3 tornillo de la parte central superior de la Campana Extractora de modo que las aberturas de de la Cubierta del Ventilador.
- Page 22 All manuals and user guides at all-guides.com 8 Sistema de Escape (Preparación del horno para Instalación) Coloque nuevamente la Cubierta del Ventilador deslizándola El siguiente paso es leer y seguir la información de montaje que se encuentra en las plantillas de pared y de dentro de las ranuras en la misma dirección de la flecha gabinete superior.
- Page 23 All manuals and user guides at all-guides.com 9 Instalación del Horno 10 Montaje del Horno en la Pared Utilization of the carton may make installation easier. Deje espacio superior al espesor de pared Pared Lado Superior Línea de Corte 2) PLACA DE MONTAJE: Coloque la Placa de Montaje con los Pernos de Anclaje sujetados, en el sitio de pared e inserte 1) MONTAJE DEL HORNO EN LA PARED: Coloque boca los Pernos y Tuercas de Anclaje a través de los orificios en...
- Page 24 PREPARACIÓN DEL HORNO. Instale los dos Filtros de Grasa 9. Lista de verificación para Instalación Viking Range Corporation • Asegúrese que la unidad ha sido instalada de acuerdo 111 Front Street con todas las Instrucciones de Instalación y las Plantillas Greenwood, Mississippi 38930 USA de Pared y las Plantillas del Gabinete Superior.