Publicité
Les langues disponibles
Les langues disponibles
F Compressor Pro
WARNING: Always wear ear protection where the sound level exceeds 85dB(A) and limit the
time of exposure if necessary. If sound levels are uncomfortable, even with ear protection,
stop using the tool immediately and check the ear protection is correctly itted and provides
the correct level of sound attenuation for the level of sound produced by your tool.
WARNING: User exposure to tool vibration can result in loss of sense of touch, numbness,
tingling and reduced ability to grip. Long term exposure can lead to a chronic condition. If
necessary, limit the length of time exposed to vibration and use anti-vibration gloves. Do not
a greater effect. Use the igures provided in the speciication relating to vibration to calculate
operate the tool with hands below a normal comfortable temperature, as vibration will have
the duration and frequency of operating the tool.
Sound and vibration levels in the speciication are determined according to EN60745 or
similar international standards. The igures represent normal use for the tool in normal
GB
working conditions. A poorly maintained, incorrectly assembled, or misused tool, may produce
increased levels of noise and vibration. www.osha.europa.eu provides information on sound
and vibration levels in the workplace that may be useful to domestic users who use tools for
long periods of time.
General Safety
WARNING Read all safety warnings and all instructions. Failure to follow the warnings
and instructions may result in electric shock, ire and/or serious injury.
WARNING: This appliance is not intended for use by persons (including children) with
reduced, physical or mental capabilities or lack of experience or knowledge unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children must be supervised to ensure that they do not
play with the appliance.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1) Work Area Safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents
b) Do not operate power tools in explosive atmospheres, such as in the presence of
lammable liquids, gases or dust. Power tools create sparks which may ignite the dust
or fumes
c) Keep children and bystanders away while operating a power tool. Distractions can
cause you to lose control
2) Electrical Safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not
use any adapter plugs with earthed (grounded) power tools. Unmodiied plugs and
matching outlets will reduce risk of electric shock
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if your body is
earthed or grounded
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock
e) When operating a power tool outdoors, use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use reduces the risk of electric shock
f) If operating a power tool in a damp location is unavoidable, use a residual current
device (RCD) protected supply. Use of an RCD reduces the risk of electric shock
3) Personal Safety
a) Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the inluence of
drugs, alcohol or medication. A moment of inattention while operating power tools may
result in serious personal injury
All manuals and user guides at all-guides.com
b) Use personal protective equipment. Always wear eye protection. Protective
c) Prevent unintentional starting. Ensure the switch is in the off-position before
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or
e) Do not overreach. Keep proper footing and balance at all times. This enables better
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing
g) If devices are provided for the connection of dust extraction and collection
4) Power Tool Use & Care
a) Do not force the power tool. Use the correct power tool for your application. The
b) Do not use the power tool if the switch does not turn it on and off. Any power tool
c) Disconnect the plug from the power source and/or the battery pack from the power
d) Store idle power tools out of the reach of children and do not allow persons
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
g) Use the power tool, accessories and tool bits etc. in accordance with these
5) Battery tool use and care
a) Recharge only with the charger speciied by the manufacturer. A charger that is
b) Use power tools only with speciically designated battery packs. Use of any other
c) When battery pack is not in use, keep it away from other metal objects, like paper
d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If
6) Service
a) Have your power tool serviced by a qualiied repair person using only identical
6
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal injuries
Carrying power tools with your inger on the switch or energising power tools that have the
connecting to power source and/or battery pack, picking up or carrying the tool.
switch on invites accidents
a key left attached to a rotating part of the power tool may result in personal injury
control of the power tool in unexpected situations
and gloves away from moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts
facilities, ensure these are connected and properly used. Use of dust collection can
reduce dust-related hazards
correct power tool will do the job better and safer at the rate for which it was designed
that cannot be controlled with the switch is dangerous and must be repaired
tool before making any adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the power tool accidentally
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users
of parts and any other condition that may affect the power tool's operation. If
damaged, have the power tool repaired before use. Many accidents are caused by
poorly maintained power tools
edges are less likely to bind and are easier to control
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended could result
in a hazardous situation
suitable for one type of battery pack may create a risk of ire when used with another
battery pack.
battery packs may create a risk of injury and ire.
clips, coins, keys, nails, screws or other small metal objects that can make a
connection from one terminal to another. Shorting the battery terminals together may
cause burns or a ire.
contact occurs, lush with water. If liquid contacts eyes, additionally seek medical
help. Liquid ejected from the battery may cause irritation or burns.
replacement parts. This will ensure that the safety of the power tool is maintained
Publicité
