Mr Handsfree iBell Set KB300 Mode D'emploi

CONTENT OF PACKAGING
Kinetic Doorbell button + 230V Receiver + Mobile Receiver + 3M Industrial tape
PARTS & BUTTONS
Mobile Receiver
230V Receiver
Kinetic Doorbell button
B: Power Plug E: ON / OFF switch
A: Doorbell button
F: Battery Compartment
C: Tone selection-button
G: Tone selection-button
D: Volume
H: Volume
INSTALLING AND PAIRING THE KINETIC DOORBELL BUTTON
You can attach the Kinetic Doorbell Button to any surface using the 3M Industrial tape or screw it into
the wall. Remove the back part of the Doorbell Button and mount 2 screws into the foreseen area to
open the plastic. Hold the back part against the wall you wish to attach it to and, by using a pencil,
indicate where you need to drill the holes. Remove the back part and drill 2 holes where the indication
is visible. Insert 2 plugs into the holes, hold the back part over and screw it in place. To finish, place the
front of the Doorbell button on the back part until it clicks in place.
You can pair multiple (optionally available on www.mrhandsfree.com) with the receivers. Simply press
the Tone-Selection (C, G) on the 230 Receiver or the Mobile receiver for 5 seconds until you hear a
sound notification. Press the doorbell-button (A) and you will hear another sound notification. After 10
seconds, you will hear another sound notification. Your devices are now paired.
INSTALLING AND PAIRING THE 230V RECEIVER
You can plug the 230V receiver into any plug desired in your house, the pairing for your set has already
been done during production.
To pair an extra 230V receiver with your doorbell button (optionally available on www.mrhandsfree.com),
press the Tone Selection button (C) for 5 seconds until you hear a sound notification. Press the Kinetic
Doorbell Button (A) and you will hear another sound notification. After 10 seconds, you will hear
another sound notification. Your devices are now paired.
INSTALLING AND PAIRING THE MOBILE RECEIVER
Before installing the Mobile receiver, insert 3x AA Alkaline batteries into the Battery Compartment (F).
Press it lightly and slide it down to open the compartment. Insert 3 AA Alkaline batteries according to
the visible scheme and close the lid again by sliding it in place until you hear a click. You can put and
take the Mobile receiver anywhere in your house (up to 150m), the pairing for your set has already
been done during production.
To pair an extra Mobile receiver with your doorbell button (optionally available on www.mrhandsfree.com),
press the Tone Selection Button (G) for 5 seconds until you hear a sound notification. Press the kinetic
doorbell button (A) and you will hear another sound notification. After 10 seconds, you will hear
another sound notification. Your devices are now paired.
SELECTING A RINGTONE AND ADJUSTING THE VOLUME
To select a ringtone on either the 230V receiver or the Mobile receiver, press the Tone selection button
of the device (C, G) until you hear the ringtone you wish to select.
Note: If you wish to have the same ringtone on both devices, you have to set it for each device separately.
Note: When multiple Kinetic Doorbell Buttons are paired to your device, it is not possible to have a
separate sound for each doorbell button.
To adjust the volume on either the 230V receiver or the Mobile receiver, first, press the Tone selection
button of the device (C, G) to hear a tune and press the Volume button of the device (D, H) to select
the desired volume.
SUPPORT
For more information, technical questions and return requests concerning this product, you should
contact support@mrhandsfree.com.
WARRANTY
Mr Handsfree is a registered trademark of TE-Group NV. The mr Handsfree brand stands for superior
product quality and outstanding customer service. That is why mr Handsfree warrants this product
against all defects in material and workmanship for a period of two (2) years from the date of original
purchase of the product. The conditions of this guarantee and the extent of responsibility of mr
Handsfree under this guarantee can be downloaded from our website: www.mrhandsfree.com.
All manuals and user guides at all-guides.com
DECLARATION OF CONFORMITY
DECLARATION OF CONFORMITY
GB
Hereby, Par la présente,
Company: Entreprise:
Address: Adresse:
declare that the following equipment: déclare que le dispositif suivant :
Product name: Nom du produit:
Product type: Type de produit:
2011/65/EC, 2014/30/EC & 2014/35/EC. Conformity is guaranteed by the CE-symbol.
versions valid in September 2016.
versions valides en Septembre 2016.
EN301489-1 V1.9.2 (2011)
EN301489-3 V1.6.1 (2013)
EN60065:2014
EN300220-1 V2.4.1 (2015)
EN300220-2 V2.4.1 (2015)
EN301489-1 V1.9.2 (2011)
EN301489-3 V1.6.1 (2013)
EN62479:2010
Joseph van Oosterum, CEO TE-Group NV
Authorised signature
ILLUSTRATIONS
TE-Group NV
Kapelsestraat 61, 2950 Kapellen, Belgium
mr. Handsfree i-Bell Set KB300
Wireless Kinetic Doorbell & Receivers
MrHandsfree iBell Set KB300
11-2016/V1
User's Manual
WIRELESS DOORBELL SET
GB NL
FR D