IPS Floodstop FS38C Guide D'installation Et D'utilisation page 4

FS38C – Toilet/Dishwasher Kit with 3/8" Compression Valve
EN
Leak Detection & Automatic Water Shut-off System Installation and Operating Manual
HELPFUL HINTS
• If the Leak Sensor Paper Sleeve is misplaced or becomes unusable,
a paper towel can be used in its place.
• The Leak Sensor has two sets of prongs which allows you to connect
additional Leak Sensors in series. By linking them together you can
achieve greater reach from the Controller Unit.
• The FloodStop valves are programmed to automatically cycle closed
and back open on their own as a self-cleaning measure to mitigate
against mineral deposits and hard water build-up. This will ensure
that the valves will function properly when needed.
• Hanging Wires may be tied together using twist ties (Not provided).
TROUBLESHOOTING
Problem What to Check
Status light does • Make sure there is power to the outlet.
not illuminate • Unplug AC Adapter cord from Control Panel
and plug back in.
• If an AC Adapter extension wire was used,
unplug both ends and reconnect.
• Make sure fresh batteries are in the
Control Panel.
• If operating only on battery power the green
"open" light will only flash intermittently.
No water comes out • Push Open button to make sure FloodStop
of valve. Valve is open.
FloodStop Valve • Make sure both sides of Sensor are dry.
does not operate • Make sure there is power to the outlet.
• Unplug AC Adapter cord from Control Panel
and plug back in.
• Unplug 6-pin connector from Control Panel
and reconnect.
• Locate plug connection between Control
Panel and the FloodStop Valve that does
not operate. Unplug the connection and
reconnect, making sure arrows on side of
plugs line up.
• If an AC Adapter extension wire was used,
unplug both ends and reconnect.
• Make sure fresh batteries are in the
Control Panel.
• Push the Close button and wait a few
seconds. Then push the Open button.
The alarm goes off • Leak Sensor is touching metal, or the
for no apparent concrete is sweating causing high humidity.
reason Correct the problem by placing the Paper
Sleeve on the Leak Sensor, or use a paper
towel as a barrier.
• To make FloodStop less sensitive to
moisture, use a flathead screwdriver to turn
the recessed button on upper left side of
control panel clockwise. NOTE: it only turns
180° and the factory setting is already in
the middle – so it should only turn 90°
either way.
MANUAL OPERATION OF FLOODSTOP VALVE
1. Unplug the connection between the control panel and the
FloodStop valve.
2. Pull the plastic motor cover off the FloodStop valve and slide it down
the wire until it stops at the plug. Note that no tools are needed to
remove the cover.
3. Use a marker and draw a line across the top of the plastic motor
housing. This way once the motor is removed you will know how to
reposition it for assembly.
4. Remove the 4 screws using a Phillips head screwdriver.
5. Place thumb and finger on plastic gear and rotate clockwise to open
valve or counter clockwise to close it. Do not use tools to manually
open or close valve.
TERMS AND CONDITIONS
Orders for this product are expressly made conditional on buyer's assent
to company's terms and conditions of sale, which can be found at
https://ipscorp.com/pdf/ipsdp-tc.pdf, or are available upon request by
mail. Any terms and conditions in any of buyer's documents that are
inconsistent with or add to seller's terms and conditions of sale are
hereby rejected and are not binding upon company.
https://ipscorp.com/pdf/ipsdp-tc.pdf
To obtain warranty service, call our customer service department at
1-800-888-8312, or e-mail us at tncustserv@ipscorp.com.
FLOODSTOP ICE MAKER KIT
This equipment has been tested and found to comply with the limits for a
class b digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy, and if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/tv technician for help.
– 4 –