Publicité
Les langues disponibles
Les langues disponibles
8
•
If you press the
PTT
code, the PMR will go back in stand-by mode on the channel with
the CTCSS code.
•
If no CTCSS code is detected there is a chance that DCS is
selected by the user. In this case you can scan for the DCS code.
(section 13.10.3)
13.10.3 Scanning for a DCS code
•
Press the
00" flashes on the display for the selected radio channel.
•
Press the
DCS scan.
Once there is a transmission on the channel, the DCS code (if used) will be detected and
displayed.
If you press the
button
PTT
PMR will go back in stand-by mode on the channel with the DCS code.
13.11 Call Tones
A call tone alerts others that you want to start talking.
13.11.1 Setting the Call Tone
The Twintalker 9500 has 15 call tones.
•
Press the
the current call tone is flashing.
•
Press the
another Call Tone.
•
Press the
mode.
13.11.2 Sending a call Tone
6
Press the
button
briefly. The call tone will be transmitted on the set channel.
13.11.3 Call tone reception type
7
•
Press the
-button
nine times.
•
Press the
-button
11
or
1. Tone only
2. Tone + vibration
3. Vibration only
Press the
-button
12
to confirm and return to stand-by mode.
PTT
button
12
while listening to a found CTCSS
7
-button
seven times : "SCAN" and "DCS
11
10
-button
or the
-button
to start the
12
while listening to a found DCS code, the
7
- button
eight times, "C" is displayed and
- button
11
or the
- button
10
to change to
- button
12
to confirm and return to stand-by
PTT
10
-button
to select the call tone reception type.
13.12 Roger Beep On/Off
After the
-button
12
is released, the unit will send out a roger beep to confirm that you have
PTT
stopped talking.
To set the Roger Beep.
• Press the
- button
• Press
button
11
Beep (OFF).
• Press the
- button
PTT
standby mode.
13.13 Key-Tone On/Off
When a button is pressed, the unit will beep briefly.
To set the key-tone.
• Press
button
• Press
button
11
Tones (OFF).
• Press the
- button
PTT
standby mode.
13.14 Dual Channel Monitor function
In stand-by, the PMR is set on one channel with CTCSS/DCS code. The PMR will only receive
signals transmitted on that channel with the CTCSS/DCS code.
Dual Channel Monitor (DCM) allows you to monitor a second channel with CTCSS/DCS code.
•
Press the
flash on the display.
•
Press the
channel.
•
Press the
and go to CTCSS selection. (Press the
again to go to DCS selection)
•
Press the
the CTCSS code or DCS code.
•
Press the
mode.
•
To disable the function select "OFF" when selecting the
DCM channel.
When the Dual Channel Monitor function is activated, the PMR will switch sequentially between
the standby channel + CTCSS/DCS code and the Dual Channel + CTCSS/DCS code.
7
ten times. 'rO' will be displayed.
to enable (ON) or
button
10
to disable the Roger-
12
to confirm your selection and return to the
7
eleven times. 'tO' will be displayed.
to enable (ON) or
button
10
to disable the Key
12
to confirm your selection and return to the.
7
-button
twelve times," DCM OFF" will
-button
11
or the
-button
10
to change the
7
-button
to confirm the channel selection
-button
-button
11
or the
-button
10
to change
-button
12
to confirm and return to stand-by
PTT
Twintalker 9500
7
Publicité
