Publicité
Les langues disponibles
Les langues disponibles
b) Adjustable Bracket
• Hold the bracket mount (11) against the wall and mark the position for the holes with a pencil.
• Use a ø6 mm diameter bit to drill holes. If needed, insert the plastic dowels using a mallet.
• Fix the bracket mount to the wall using the supplied screws.
• Slide the mounting bracket into the bracket mount slot (8).
• Make sure the attachment is secure before letting go.
- Gently adjust the angle of the main unit on the bracket to optimise the sensor detection
angle.
- You can test the setup by approaching the sensor from outside the detection range at
different angles.
• Tighten the bracket tensioner screw (12) to lock the bracket position.
Hanging Slot
You can hang the main unit ontoa wall from the hanging slot (7). If you are not using
the supplied screws make sure the screw head will fit into the hanging slot (7).
When screwing in, the head should slightly protrude to provide a secure fixing point.
The motion detection angle cannot be adjusted when mounted via the hanging slot
(7), so make sure the position is suitable before drilling.
• If no suitable screws are already in place, use a supplied screw and dowel (if needed).
• Use a ø6 mm diameter bit to drill holes. If needed insert the plastic dowels using a mallet.
Insert Batteries
The main unit can also be connected to the mains power supply via DC power input
(6). The adaptor is not included.
The internal battery circuit will disconnect when the device is connected to an
external power supply, but it is recommended to remove the batteries first.
Battery life will depend on the ambient temperature, and how often the main unit and
remote control are activated.
a) Main Unit
• To access the battery compartment, first slide the bracket mount (11) off if needed.
• Remove the battery compartment cover (10) by pulling it away using the cover tab (9).
• Insert 3 x AAA type batteries, matching polarities as shown in the compartment.
• Replace the battery compartment cover (10).
If the alarm or doorbell melody volume gets low, you may need to replace the
batteries on the main unit.
b) Remote Control
• Remove the battery compartment cover (18) by gently pulling it away from the cover tab.
• Insert the included CR2032 type battery, with the positive polarity "+" facing upwards.
• Replace the battery compartment cover (18).
If the LED button press indicator (13) does not light up, replace the batteries on the
remote control.
Operation
a) Main Unit
Motion Sensor Alarm
• Turn the unit ON (5). The default mode will be doorbell.
• Press and hold SET (4) for 3 seconds to enter alarm mode.
• A short sound will indicate you are in alarm mode.
The motion detector (1) will now be active. If movement is detected within the sensor range,
it will trigger the alarm.
It will take approximately 35 seconds for the motion detector to reset after the alarm
has been triggered.
All manuals and user guides at all-guides.com
Doorbell
• Turn the main unit ON (5). The default mode will be doorbell.
• If in alarm mode, press and hold SET (4) for 3 seconds to enter doorbell mode.
• A short sound will indicate you are in doorbell mode.
• Press the SET (4) button to shuffle through 16 different melodies.
b) Remote Control
• With the main unit switched ON (5), you can press the Doorbell (17) or alarm button (15) to
• Press the Select (16) button to shuffle through 16 different melodies.
Care and Cleaning
• Before each cleaning, turn the device OFF (5), and disconnect the product from the mains.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as
• Clean the product with a dry, fibre-free cloth.
Disposal
a) Product
b) Batteries
Used batteries can be returned to collection points in your municipality, our stores or wherever
batteries are sold.
You thus fulfill your statutory obligations and contribute to the protection of the environment.
Technical Data
Power source (main unit) .............. 5 V/DC, 1 A (adaptor not included)
Battery (remote) ............................ 1 x 3V CR2032 (included)
Battery Life ................................... Max. 1 yr (main unit)
Alarm Volume ............................... Max. 115 dB
Doorbell ........................................ 16 melodies
Doorbell volume ............................ Max. 105 dB
PIR detection angle ...................... Approx. 120 º (vertical and horizontal)
PIR detection distance .................. Max. 5 m
Remote control range ................... Approx. 5 m
Operating / storage conditions ...... -20 to +45 °C, 0 – 85 % relative humidity
Dimensions (L x W x H) ................ 66 x 25 x 131mm
Weight .......................................... 145 g (excluding battery)
If you turn the unit OFF or replace the batteries, the selected melody will return to
the factory default.
You must be within range of the main unit and there should be a clear line of sight
between infrared transmitter (14) and the infrared receiver (2).
If you cannot control the main unit using the remote control, check if the battery on
the remote control needs to be replaced.
activate your preferred mode.
they can cause damage to the housing and malfunctioning.
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product in accordance
with applicable regulatory guidelines.
Remove any inserted batteries and dispose of them separately from the product.
You as the end user are required by law (Battery Ordinance) to return all used
batteries. Disposing of them in the household waste is prohibited.
Contaminated batteries are labeled with this symbol to indicate that disposal in
the domestic waste is forbidden. The designations for the heavy metals involved are:
Cd = Cadmium, Hg = Mercury, Pb = Lead (name on batteries, e.g. below the trash icon
on the left).
3 x 1.5 V, AAA (not included)
Max. 1 yr (remote control)
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights
including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represents the technical status at the time of printing.
Copyright 2018 by Conrad Electronic SE.
*1761037_v1_1218_02_dh_m_en
Publicité
