Suncourt FLUSH FIT REGISTER BOOSTER HC500 Manuel D'instructions

OPERATION INSTRUCTIONS FOR THE FLUSH FIT
READ AND SAVE THESE INSTRUCTIONS
IMPORTANT NOTICE
With the use of any electrical appliance, it is important to observe all basic precautions to minimize the risk associated with use, such as electrical shock, fire,
or injury to persons. Read these instructions before using your Flush Fit
NEVER EXPOSE YOUR FLUSH FIT™ REGISTER BOOSTER™ TO TEMPERATURES OVER 140°F (60°C)
INSTALLATION
DO NOT INSTALL IN CEILING.
FLOOR REGISTER 4" X 10"
1. Plug the small molded end of the power cord into the top of the Flush Fit
Register Booster .
™
2. Plug the wall transformer end of the power cord into a 120 Volt AC outlet.
3. Follow directions for OPERATION SETTINGS before placing in register.
4. Remove floor register and replace with the Flush Fit
CLEANING AND MAINTENANCE
Before cleaning the Flush Fit
™
the round brush attachment of your vacuum cleaner, or a cloth that has been lightly moistened with water and a mild, non-abrasive detergent. Dust accumulation
in the interior of the unit may be removed by using the small round brush attachment of your vacuum cleaner.
Accumulation of dust in the interior will be minimized by regular replacement of your furnace filter as
recommended by the manufacturer.
IMPORTANT WARNINGS
1. The Flush Fit Register Booster
™
temperature for the register is 140° Fahrenheit or
60° Centigrade. Your Flush Fit
™
2. Do not in any way block the air grilles of the Flush Fit
3. Unplug the Flush Fit Register Booster
™
4. Do not operate the Flush Fit
otherwise damaged, or if the housing is damaged or broken. Discard or return the unit for inspection, replacement, or repair.
5. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange
cord away from traffic area and where it will not be tripped over.
6. The Flush Fit Register Booster
™
in contact with water.
7. The Flush Fit Register Booster
™
8. Place the Flush Fit Register Booster
™
9. Never insert any object or allow any object to enter the Flush Fit
to malfunction.
10. Do not use the Flush Fit Register Booster
™
11. The Flush Fit Register Booster
™
injury to persons and will void any warranty by the manufacturer.
12. If it is necessary to use an extension cord, use a minimum 18 gauge cord.
13. Pressure on the bottom or top grilles of the Flush Fit
14. Do not use strong detergents or flammable liquids to clean the Flush Fit
15. The housing of your Flush Fit
SERVICEABLE PARTS INSIDE. Attempting to open the housing will expose you to dangerous electricity, may cause fire and will void any and all warranty.
All manuals and user guides at all-guides.com
Register Booster
™
Wall Mount Drill Hole Location
Register Booster disconnect the power cord from the outlet. Dust may be removed from the exterior surfaces using a soft cloth,
™
will be as warm as the air that is delivered from the register of your forced air furnace and/or cooling system. The maximum
™
Register Booster should never be exposed to higher temperatures or temperatures below freezing.
™
Register Booster
™
when not in use. Turn the unit off before unplugging.
™
Register Booster with a damaged plug or cord, if the unit malfunctions, becomes noisy when operating, has been dropped or
™ ™
should never be exposed to moisture. Do not use the unit in an open window, bathroom, or laundry area where it may come
™
is designed for indoor use only.
™
and the electrical cord where it will not be tripped over, and is out of the traffic pattern.
™
near flammables such as gasoline, paint, or natural gas.
™
is intended for use as described in the instructions only. Other use may cause fire, electrical shock, damage to the unit, or
™
Register Booster
™
Register Booster is sealed at the factory. THERE ARE NO
™ ™
Register Booster .
™ ™
WALL REGISTER 4" X 10"
1. Drill (two) holes with a 3/16" drill bit from the bottom side of the Flush Fit
Register Booste grille. The holes should be drilled in the pre-molded location
™ as pictured below.
2. Plug the small molded end of the power cord into the top of the Flush Fit
Register Booster
3. Plug the wall transformer end of the power cord into a 120 Volt AC outlet.
.
4. Follow directions for OPERATION SETTINGS before placing in register.
™
5. Remove the wall register and replace with the Flush Fit
6. Secure the Flush Fit
.
™
Register Booster through the bottom or top grilles, as this may damage the unit or cause it
™ ™
may cause the fan impeller to contact these grilles and damage the unit.
™
Register Booster .
™ ™
REGISTER BOOSTER
™
.
™
Register Booster in place.
™ ™
™
MODEL: HC500
™
™
Register Booster .
™ ™