Télécharger Imprimer la page

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

FORM FIT
HOOD PROTECTOR
Mazda MPW 2004 -
Hardware Kit
2 – Pedestal Clips
– 2 Pedestal Clips already attached to the protector
1 – 3M Adhesion Promoter
4 – 3M Anti-abrasion Film Pads
4 – Black "C" Clips
4 – #6 x 3/8" Black Truss Head Screws
4 – #4x 3/16" Black Truss Head Screws
2 – Large Bumpons
Installation
1.
Be sure that the hood is clean and dry. Release the hood latch (it is not necessary to open the hood at this time).
2.
Apply the adhesive promoter to the 2 (two) areas shown below where the mounting pedestals will attach. Follow the instructions on the promoter for
use. Allow the adhesive promoter to dry. See Illustration #1.
3.
Peel the protective backing from the tape with the open end of the pedestals facing forward, place the pedestals into place on the hood. Press down
firmly on each mounting pedestal to make sure they are properly adhered. See Illustration #1.
4.
Position the protector on the hood by engaging the hooks on the pedestals attached to the protector with those on the pedestals installed on the
hood. Make sure that the protector is centered.
5.
Attach the anti-abrasion film pads to the hood in line with the holes in the leading edge of the protector. Fold the pads in half over the hood edge to
cover at least ½" of the underside of the hood. See Illustration #2 & #3.
6.
Slide the "C" clips on the hood in line with the holes in the protector. Be sure that the "C" clips are well seated against the hood; it may be necessary
to tap on the clips. See Illustration #2.
7.
Be sure that the hole in the top of the clips lines up with the hole in the protector, then tighten the #6 x 3/8" screws, through the protector and into the
top of the "C" clips. Do not over tighten. See Illustration #3.
8.
Make sure all the clips are well seated against the hood. Tighten the #4 x 3/16'' screws in the back of the "C" clips. See Illustration #3.
9.
Install the (2) two bumpons as shown in illustration #2. Attention: the bumpons must be installed on the hood, not on the protector!!! If the
bumpons are installed on the protector, they may wear through the paint.
10. On some vehicles it may be necessary to adjust the hood bumpers and/or latch for proper clearance.
Note: Do not pull on the protector when opening or closing the hood.
Care Instructions
Clean the protector with a mild soap and water solution or plastic cleaner only. Do not use chemicals or solvents.
Periodically check to make sure the bumpons are in place and the protector is secure.
Avoid using automatic car washes. Do not pull on the protector when opening or closing the hood.
Illustration # 1: Pedestal Location
Illustration # 2: Bumpon and Clip Location
Thank you for purchasing a Form Fit hood protector.
Retain this sheet for care instructions and hardware kit information.
Made in Canada
All manuals and user guides at all-guides.com
1 ½"
6"
Bumpons
Clips
Tools Required
1 – Phillips Screwdriver
1 – Tape Measure
Protector
Illustration # 3: Clip Configuration
HDW 11D 04
Hood
Pedestal Clips
Rev0.040511

Publicité

loading

Sommaire des Matières pour FORM FIT HDW 11D 04

  • Page 1 Hood Pedestal Clips Illustration # 2: Bumpon and Clip Location Illustration # 3: Clip Configuration Bumpons Clips Thank you for purchasing a Form Fit hood protector. Retain this sheet for care instructions and hardware kit information. Rev0.040511 Made in Canada...
  • Page 2 Illustration n°2: Emplacement des butées et des agrafes Illustration n°3: Configuration de l’agrafe Bumpons Clips Merci de vous êtes procuré un protecteur form fit. Conserver cette feuille pour les instructions d’entretien et les renseignements concernant le nécessaire d’installation. Fabriqué au Canada Rev0.040511...