Accessories; Environmental Protection; Technical Specifications - Metabo WEF 9-125 Mode D'emploi

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

able for the material being processed. Do not tilt,
apply excessive force or sway from side to side.
Wire brushing:
Press down the machine evenly.
8. Cleaning
Motor cleaning: blow compressed air through the
rear ventilation slots of the machine regularly,
frequently and thoroughly. Here, the machine must
be held firmly.
Clean the dust filter regularly: remove and clean
with a jet of compressed air.
9. Troubleshooting
9.1
Mains powered machines:
- Overload protection: There is a MAJOR
reduction in load speed. The motor temperature
is too high! Allow the machine to run at idle speed
until it has cooled down.
- Overload protection: There is a SLIGHT
reduction in load speed. The machine is over-
loaded. Reduce the load before continuing to
work.
- Metabo S-automatic safety shutdown: The
machine was SWITCHED OFF automatically. If
the slew rate of the current is too high (for
example, if the machine suddenly seizes or kick-
back occurs), the machine switches off. Switch off
the machine at the slide switch (6). Switch it on
again and continue to work as normal. Try to
prevent the machine from seizing. See section
3.2.
- Restart protection: The machine does not
start. The restart protection is active. If the mains
plug is inserted with the machine switched on, or if
the current supply is restored following an inter-
ruption, the machine does not start up. Switch the
machine off and on again.
9.2
Cordless machines:
- The electronic signal display (10) lights up
and the load speed decreases. The tempera-
ture is too high! Run the machine in idling until the
electronics signal indicator switches off.
- The electronic signal display (10) flashes and
the machine does not start. The restart protec-
tion is active. The machine will not start if the
battery pack is inserted while the machine is on.
Switch the machine off and on again.

10. Accessories

Use only genuine Metabo accessories.
See page 4.
Use only accessories that fulfil the requirements
and specifications listed in these operating instruc-
tions.
A Safety guard for cut-off grinding
Designed for work with cut-off wheels, diamond cut-
off wheels.
Install as described under "Safety guard for
grinding" (chapter 5.4).
B Hand guard for sanding and wire brushing
operations
Designed for work with support plates, sanding
pads, wire brushes.
Install hand guard under the additional side-
mounted handle.
C Chargers
D Battery packs
For a complete range of accessories, see
www.metabo.com or the accessories catalogue.
11. Repairs
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
If you have Metabo electrical tools that require
repairs, please contact your Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.

12. Environmental Protection

The sanding dust generated may contain
hazardous materials: do not dispose of with the
household waste, but at a special collection point
for hazardous waste.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Special instructions for cordless machines:
Battery packs must not be disposed of with regular
waste. Return faulty or used battery packs to your
Metabo dealer!
Do not allow battery packs to come into contact with
water!
Before disposal, discharge the battery pack in the
power tool. Prevent the contacts from short-circu-
iting (e. g. by protecting them with adhesive tape).

13. Technical specifications

Explanation of details on page 3. Subject to
changes serving technical progress.
U
= Voltage of battery pack
D
= max. diameter of accessory
max
t
= Max. permitted thickness of clamping
max,1
shank on accessory when using
clamping nut (16)
t
= Roughing wheel/cut-off wheel:
max,3
max. permissible thickness of the
accessory tool
M
= Spindle thread
l
= Length of the grinding spindle
n*
= No-load speed (maximum speed)
I
= Current at 120 V
120 V
P
= Nominal power input
1
P
= Power output
2
m
= Weight with smallest battery pack/
weight without cord
ENGLISH en
11

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Wepf 9-125Wf 18 ltx 125Wpf 18 ltx 125613060420613069420613070860 ... Afficher tout

Table des Matières