Publicité
Les langues disponibles
Les langues disponibles
• The device is not a toy. Children cannot judge
the dangers of electrical devices and lasers.
• Laser has radiation; please do not look directly,
so as not to damage the eyes.
Direct the laser beam in a way that it is not at
eye level. The intense light rays could temporarily
impair your eyesight. Moreover, they may trigger
epileptic seizures in vulnerable persons. This ap-
plies in particular to epileptics.
• Please do not place the laser light near high
temperature or near fire.
• Do not point the laser beam at mirrors or other
reflective surfaces. The uncontrolled,
reflected beam may strike people or animals.
• Only operate the laser in an attended area.
• Limit the area of beams as far as possible by
using screens or dividing walls.
• Please use the matching power adapter.
• Please turn off the power if not use for a long
time, don't expose in the outdoors of harsh envi-
ronment. Please do not disassemble the product,
including the shell and converter.
• In low temperature environment, the laser light
needs to automatically heat for some time to
reach the normal working condition, it is a nor-
mal phenomenon.
Installation instruction
• Connect to plug: Align the interface of laser
lamp bottom, clockwise rotation, tighten (fig 1);
Insert the product into the ground to ensure sta-
bility; If the ground is dry, can be wet with water,
so as not to damage the product.
• Connect the tray: Align the interface of laser
lamp bottom, clockwise rotation, tighten (fig 2);
Place the product in the right place.
• Laser light irradiation angle adjustment: Coun-
terclockwise loosen nuts, adjust the angle of the
laser light irradiation, then tighten the nut clock-
wise (fig 3);
• Connect power adapter: Plug one end of the
power cord into the power adapter connector,
clockwise tighten the anti-water dust cover (fig 4),
turn on the power switch, you can use.
All manuals and user guides at all-guides.com
• Connect power adapter: Plug one end of the
power cord into the power adapter connector,
clockwise tighten the anti-water dust cover (fig 4),
turn on the power switch, you can use.
Fig.1
Fig.2
Fig.3
Remote control instructions
"Power":Switch control button
"MODE": Laser color conversion button
"FLASH": Laser flash control button
"+""-": Laser rotation speed increase / decrease
control button
"2H": Set the working time of 2 hours, the clos-
ingtime of 22 hours, 24 hours for a cycle, auto-
matic cycle;
"4H": Set the working time of 4 hours, the closing
time of 20 hours, 24 hours for a cycle, automatic
cycle;
"6H": Set the working time of 6 hours, the closing
time of 24 hours, 24 hours for a cycle, automatic
cycle;
"8H": Set the working time of 8 hours, the closing
time of 16 hours, 24 hours for a cycle, automatic
cycle;
"RESET": Cancel the timer setting.
www.Deuba24online.de
Timing function
Laser light default 6 hours at regular time, when
power on, the timing function could automati-
cally operation(calculate the time when start ,
works 6 hours, stops working 18 hours, 24 hours
cycle). The"RESET" key on Remote control can
cancel the timing function.Use the power button
on the remote control to turn off the laser light,
when you turn on again, the timing function has
Fig.4
been canceled. Select the time button on the
Remote control, set the timing time; unplug the
laser light power, energized again, the default
timing function will roll-back.
Maintenance and Care
• Always turn off the appliance before perform-
ing any maintenance or checks.
• Never switch the laser effect device on and off
at short intervals. This will considerably reduce
the service life of the device.
• The device is not suitable for continuous use.
Pauses in operation increase the service life of
the product.
• Check all parts for signs of wear. If any prob-
lems are detected, do not use the product. Al-
ways replace all parts with original replacements
according to the manufacturer's guidelines.
• If the product is not properly cared for and
maintained, it can become unsafe and can also
become damaged. This can lead to dangerous
situations.
Product parameters
Applicable voltage:GS 230V 50HZ
Power adapter: 12 V 1A
Power cord length: 3 meter
Laser wavelength: Red laser (650nm) Green laser
(520nm)
Laser Classification: Class 3R(American);Class
II(Europe)
Waterproof level: IP44
Remot control battery : CR2032
Remote control effective distance : <15 meters
Application scope: Indoor and outdoor
6
7
www.Deuba24online.de
Publicité
