NightStick 4608 Instructions

Model 4608 / 4610 Headlamp Instructions
Multiple Patents Pending
INS-4608-13
CAUTION: DO NOT use in explosive atmospheres, near flammable liquids,
or where explosion proof lamps are required
DO NOT use in the proximity of vehicles or equipment when there is a risk of flammable
liquids coming into contact with the hand-lamp
CAUTION: For Light Duty Use Only
WARNING: NOT FOR USE ABOVE HAZARDOUS LOCATIONS
Thank you for purchasing this Nightstick headlamp. Save these instructions.
Please read these instructions before using your headlamp.
INSTALLING BATTERIES
1. Unscrew the battery compartment door on the back of the headlamp.
2. Insert the batteries per the outline inside the battery compartment. Observe the
correct polarity of the batteries.
3. Close the battery door and fasten the battery compartment door screw.
4. The headlamp is now ready for use.
BATTERY NOTES
• Batteries may lose power when stored for long periods.
• Alkaline batteries can leak and cause corrosion if stored for long periods. Always
remove batteries if the light will be unused for extended periods.
• Batteries should be stored between 68-78°F (20-25°C)
SAFETY
CAUTION BRIGHT LED RADIATION: AVOID DIRECT EYE EXPOSURE. The light is a
Class 2 LED product per IEC 60825-1 Edition 1.2.2001.
Do not use this headlamp in explosive or hazardous areas.
•
OPERATION
Two switches control all functions on both models.
NSP-4608B
SPOTLIGHT SWITCH
First Press = spotlight full power
Second Press = spotlight half-power
Third Press = off
All manuals and user guides at all-guides.com
Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • www.baycoproducts.com
FLOODLIGHT SWITCH
First Press = floodlight full power
Second Press = floodlight half-power
Third Press = off
NSP-4610B
SPOTLIGHT SWITCH
First Press = spotlight full power
Second Press = spotlight half-power
Third Press = off
FLOODLIGHT SWITCH
First Press = white floodlight
Second Press = red floodlight
Third Press = green floodlight
Fourth Press = off
HEADBAND
The headband is elastic with a non-slip texture and fits easily and securely directly on the
head or on a hardhat.
WARRANTY
Limited Lifetime Warranty
Product is warranted to be free from defects in workmanship and materials for the
lifetime of the original owner. Includes the housing, lenses, electronics and switches.
Batteries, normal wear and abuse are excluded.
Not Covered
Consequential damages, incidental damages or incidental expenses, including damage
to property. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you. This
warranty gives you specific legal rights, which may vary from state to state.
Warranty Claims - USA
Contact Bayco for USA warranty claims. Call 800-233-2155 or email
cs@baycoproducts.com and Bayco Customer Service will provide a Return Goods
Authorization (RGA) to facilitate rapid warranty action. After receiving the RGA, send the
product (shipping prepaid) to BAYCO • 640 S. SANDEN BLVD • WYLIE, TEXAS • 75098.
Include a dated proof of purchase and a brief description of the defect with your name,
address and phone number. Your product will either be repaired or replaced at the option
of Bayco and returned as soon as practical, but no later than 45 days after being
received by Bayco.
Warranty questions and international claims
If you live outside the USA or have questions about this warranty or an inquiry about
other Bayco products contact BAYCO • 640 S. SANDEN BLVD • WYLIE, TEXAS • 75098
or call 800-233-2155
Instructions Lampe Tete Modèle 4608/ 4610
Brevets multiples en attente
ATTENTION: NE PAS utiliser des lampes dans des atmosphères explosives, à proximité
de liquides inflammables, ou lorsque l'épreuve des explosions sont nécessaires
NE PAS utiliser à proximité de véhicules ou d'équipement quand il ya un risque de
liquides inflammables d'entrer en contact avec la main-lampe
ATTENTION: Pour Light Duty Utilisez uniquement
AVERTISSEMENT: NE PAS UTILISER POUR CI-DESSUS DES ENDROITS
DANGEREUX
Merci d'avoir acheté cette lampe de poche Nightstick. Conservez ces instructions.
S'il vous plaît lire attentivement ces instructions avant d'utiliser votre lampe de poche.
INSTALLATION DES PILES
1. Dévissez le couvercle du compartiment de la batterie à l'arrière du projecteur.
2. Insérez les piles selon le plan à l'intérieur du compartiment à piles. Respectez la
polarité des piles.
3. Fermez le couvercle des piles et serrer la vis du compartiment des piles de la porte.
4. Le projecteur est maintenant prêt à l'emploi.
REMARQUES SUR LA BATTERIE
Les batteries peuvent perdre de la puissance lorsqu'il est stocké pendant de longues
•
périodes.
Les piles alcalines peuvent fuir et provoquer la corrosion s'il est stocké pendant de
•
longues périodes. Toujours retirer les piles si la lumière ne sera pas utilisée pendant
de longues périodes.
Les piles doivent être conservés entre 20-25 ° C
•
SÉCURITÉ
ATTENTION rayonnement lumineux LED: Evitez toute exposition directe. La
lumière est un produit de classe 2 LED par IEC 60825-1 Edition 1.2.2001.
Ne pas utiliser cette lampe de poche dans les zones explosives ou dangereuses.
•
FONCTIONNEMENT
Deux interrupteurs contrôlent toutes les fonctions sur les deux modèles.
NSP-4608B
PLEINS FEUX COMMUTATEUR
Appuyez d'abord sur = projecteurs à pleine puissance
Deuxième Appuyez sur = projecteurs à mi-puissance
Troisième pression = eteindre