Publicité
Installation Instructions
NTE-864/J
MAX Mini LED Track Head with J-Style Adapter
INPUT RATING
OUTPUT RATING
13W 120VAC 60Hz
36VDC 310mA
IMPORTANT SAFETY INSTRUCTION (READ ALL INSTRUCTIONS)
When installing or using this luminaire, basic safety precautions should always be followed, including the following:
For use with Juno "T" track system.
CONSIGNES DE SÉCURITÉ IMPORTANTES (LISEZ TOUTES LES INSTRUCTIONS)
Lors de l'installation ou de l'utilisation de ce luminaire, il vous faut toujours respecter les consignes de sécurité de base, y compris les suivantes.
À utiliser avec le système de chenilles Juno "T".
• Do not install this luminaire in damp or wet locations / N'installez pas ce luminaire dans des emplacements humides ou mouillés
• Do not install any part of this luminaire less than 5 feet above the floor / N'installez aucune section de ce luminaire à moins de 1,52 m (5 pi) au-dessus du sol
• Do not install any luminaire assembly closer than 6 inches from any curtain, or similar combustible material / N'installez aucun luminaire à moins de 15,24 cm (6 po) de tout rideau ou autre matériau combustible similaire
• Disconnect electrical power before adding to or changing the configuration of the track / Coupez l'alimentation électrique avant d'ajouter à la configuration du rail ou de la modifier
• Do not attempt to energize anything other than lighting track luminaires on the track. To reduce the risk of fire and electric shock, do not attempt to connect power tools, extension cords, appliances, and the
like to the track / Ne tentez pas d'alimenter un appareil autre que des luminaires pour rail d'éclairage sur le rail. Pour réduire les risques d'incendie et de choc électrique, n'essayez pas de brancher des outils électriques,
des rallonges, des appareils ménagers et autres produits du genre sur le rail.
SAVE THESE INSTRUCTIONS / CONSERVEZ CES INSTRUCTIONS
INSTALLATION
INSTALLATION INSTRUCTIONS TO SINGLE CIRCUIT TRACK SYSTEM:
NOTE: All Juno track sections have an embossed line (Figure 1) that indicates the track
polarity. All track fixture adapters have raised arrows (Figure 2) that point to the
polarity line when they are installed on the track section.
1. To attach fixture to single circuit track, insert "Adapter Contacts" (Figure 2) into track
channel. Track fixture should be off.
2. Rotate adapter 1/4 turn (90°) so that polarity arrows point at the polarity line on the
track.
3. Juno track fixture adapter have an on-off switch. Switch "on" position is
opposite "Locking" lever.
FOR ADAPTER WITHOUT THE LOCKING LEVER: Insert the adapter into the track and twist
the adapter and ground contact towards the polarity grove. (Figure 5)
Figure 1
Embossed
Polarity
Line
Figure 5
Polarity Line
Track
Adapter
6505 Gayhart Street, Commerce, CA 90040
Tel 323.767.2600 | www.noralighting.com | e-mail: nora@noralighting.com
© 2022 Nora Lighting, Inc. All rights reserved. Instructions subject to change without notice.
Figure 2
Figure 3
Locking
Adapter
Lever
Contacts
Adapter
Switch
Polarity
Indicating
Arrows
READ PRIOR TO ATTEMPTING INSTALLATION
ALWAYS TURN OFF MAIN POWER BEFORE INSTALLATION
INSTALLATION SHOULD BE CARRIED OUT BY YOUR LOCAL ELECTRICIAN
INSTALLATION INSTRUCTIONS TO TWO CIRCUIT TRACK SYSTEM:
NOTE: For two circuit installation, the "Positive Contact" - (marked "P" - see Figure 3) must be in
lower position for single circuit and in raised position for two circuit.
1. To install track fixture on 2nd (upper) circuit, raise "Positive Contact" by inserting a thin
screwdriver under the contact and lifting upward (Figure 3).
2. Insert a "Contact Support" under the raised "Positive Contact" (Figure 4). (These "Positive
Contact Supports" are supplied with all Juno Two Circuit Track sections.)
3. To attach fixture to two circuit track, insert "Adapter Contacts" (Figure 2) into track channel.
Track fixture should be off.
4. Rotate adapter 1/4 turn (90°) so that polarity arrows point at the polarity line on the track.
5. Juno track fixture adapter have an on-off switch. Switch "on" position is opposite "Locking"
lever.
FOR ADAPTER WITHOUT THE LOCKING LEVER: Raise "Positive Contact" by inserting the
screwdriver under the contact and lifting upward. (Figure 3) Insert the adapter into the track
and twist the adapter and ground contact towards the polarity grove. (Figure 5)
Positive Contacts
Positive Contacts
Figure 4
In Raised Position
Contact
Support
051622P3
IS-NTE-866-R01
Publicité
