Publicité
Les langues disponibles
Les langues disponibles
Guidance and manufacturer's declaration –electromagnetic emissions
Guidance and manufacturer's declaration –electromagnetic emissions
®
®
The WiTouch
and WiTouch
Pro are intended for use in the electromagnetic environment specified below. The customer or the user of the WiTouch
or WiTouch Pro should assure that it is used in such an environment.
®
®
The WiTouch
and WiTouch
Pro are intended for use in the electromagnetic environment specified below. The customer or the user of the WiTouch
or WiTouch Pro should assure that it is used in such an environment.
Emissions test
Emissions test
RF emissions
CISPR 11
RF emissions
CISPR 11
RF emissions
CISPR 11
RF emissions
Harmonic emissions
CISPR 11
IEC 61000-3-2
Harmonic emissions
Voltage fluctuations /
IEC 61000-3-2
flicker emissions
Voltage fluctuations /
IEC 61000-3-3
flicker emissions
IEC 61000-3-3
Guidance and manufacturer's declaration –electromagnetic immunity
Guidance and manufacturer's declaration –electromagnetic immunity
The WiTouch and WiTouch Pro are intended for use in the electromagnetic environment specified below. The customer or the user of the WiTouch or
WiTouch Pro should assure that it is used in such an environment.
The WiTouch and WiTouch Pro are intended for use in the electromagnetic environment specified below. The customer or the user of the WiTouch or
WiTouch Pro should assure that it is used in such an environment.
Immunity test
IEC 60601 test level
Immunity test
IEC 60601 test level
Electrostatic discharge
±6 kV contact
(ESD)
Electrostatic discharge
±6 kV contact
±8 kV air
(ESD)
IEC 61000-4-2
±8 kV air
IEC 61000-4-2
Electrical fast
±2 kV for power supply lines
transient/burst
Electrical fast
±2 kV for power supply lines
±1 kV for input/output lines
transient/burst
IEC 61000-4-4
±1 kV for input/output lines
IEC 61000-4-4
Surge
±1 kV differential mode
Surge
±1 kV differential mode
IEC 61000-4-5
±2 kV common mode
IEC 61000-4-5
±2 kV common mode
Voltage dips, short
<5 % U
T
interruptions and voltage
(>95 % dip in U
)
T
Voltage dips, short
<5 % U
variations on power supply
for 0.5 cycle
T
(>95 % dip in U
interruptions and voltage
)
input lines IEC 61000-4-11
T
variations on power supply
for 0.5 cycle
40 % U
T
input lines IEC 61000-4-11
(60 % dip in U
)
T
40 % U
for 5 cycles
T
(60 % dip in U
)
T
for 5 cycles
70 % U
T
(30 % dip in U
)
T
70 % U
for 25 cycles
T
(30 % dip in U
)
T
for 25 cycles
<5 % U
T
(>95 % dip in U
)
T
<5 % U
for 5 sec
T
(>95 % dip in U
)
T
for 5 sec
Power frequency (50/60
Hz) magnetic field IEC
3 A / m
Power frequency (50/60
61000-4-8
Hz) magnetic field IEC
3 A / m
61000-4-8
NOTE U
is the a.c. mains voltage prior to application of the test level.
T
NOTE U
is the a.c. mains voltage prior to application of the test level.
T
Compliance
Electromagnetic environment – guidance
Compliance
The WiTouch and WiTouch Pro use RF energy only for its internal
Electromagnetic environment – guidance
Group 1
function. Therefore, its RF emissions are very low and are not likely to
The WiTouch and WiTouch Pro use RF energy only for its internal
cause any interference in nearby electronic equipment.
Group 1
function. Therefore, its RF emissions are very low and are not likely to
cause any interference in nearby electronic equipment.
Class B
The WiTouch and WiTouch Pro are suitable for use in all establishments
Class B
other than domestic and those directly connected to the public low-
Not applicable
The WiTouch and WiTouch Pro are suitable for use in all establishments
voltage power supply network that supplies buildings used for domestic
other than domestic and those directly connected to the public low-
purposes.
Not applicable
voltage power supply network that supplies buildings used for domestic
Not applicable
purposes.
Not applicable
Compliance level
Compliance level
±6 kV contact
±6 kV contact
±8 kV air
±8 kV air
±2 kV for power supply lines
±2 kV for power supply lines
±1 kV for input/output lines
±1 kV for input/output lines
±1 kV differential mode
±1 kV differential mode
±2 kV common mode
±2 kV common mode
<5 % U
T
(>95 % dip in U
)
T
<5 % U
for 0.5 cycle
T
(>95 % dip in U
)
T
for 0.5 cycle
40 % U
T
(60 % dip in U
)
T
40 % U
for 5 cycles
T
(60 % dip in U
)
T
for 5 cycles
70 % U
T
(30 % dip in U
)
T
70 % U
for 25 cycles
T
(30 % dip in U
)
T
for 25 cycles
<5 % U
T
(>95 % dip in U
)
T
<5 % U
for 5 sec
T
(>95 % dip in U
)
T
for 5 sec
3 A / m
3 A / m
–
Electromagnetic environment
guidance
–
Electromagnetic environment
guidance
Floors should be wood, concrete or
ceramic tile. If floors are covered with
Floors should be wood, concrete or
synthetic material, the relative
ceramic tile. If floors are covered with
humidity should be at least 30 %.
synthetic material, the relative
humidity should be at least 30 %.
Mains power quality should be that of
a typical commercial or hospital
Mains power quality should be that of
environment.
a typical commercial or hospital
environment.
Mains power quality should be that of
a typical commercial or hospital
Mains power quality should be that of
environment.
a typical commercial or hospital
environment.
Mains power quality should be that of
a typical commercial or hospital
Mains power quality should be that of
environment. If the user of the
a typical commercial or hospital
[
or
] requires
EQUIPMENT
SYSTEM
environment. If the user of the
continued operation during power
[
or
] requires
mains interruptions, it is
EQUIPMENT
SYSTEM
continued operation during power
recommended that the [
or
EQUIPMENT
mains interruptions, it is
] be powered from an
SYSTEM
recommended that the [
or
uninterruptible power supply or a
EQUIPMENT
] be powered from an
battery.
SYSTEM
uninterruptible power supply or a
battery.
Power frequency magnetic fields
should be at levels characteristic of a
Power frequency magnetic fields
typical location in a typical commercial
should be at levels characteristic of a
or hospital environment.
typical location in a typical commercial
or hospital environment.
Publicité
