Publicité
Les langues disponibles
Les langues disponibles
Triple Zone. The Triple Zone Indicator will
illuminate to confirm this.
Pressing
again will switch off the Triple
Zone of the heater. Each operation causes
a status change of the Dual and Triple
Zones in the following manner: dual zone
on/off, triple zone on, all extended zones
off, dual zone on/off, triple zone on, all
zones off, and so on.
Set Cooking Level with and without Heat
Boost
All heaters are equipped with the heat
boost function.
If the heat boost is required, set the heat to
0 using the slider then to level 9. Once level
9 has been reached, the display will flash
"A" alternating with the heat setting value
"9" to show the heat boost is active.
If the heat boost is active, the heater will
operate with maximum power for a period of
time dependent on the heat setting selected
before the heat boost was activated.
Once the heat boost time has ended, only
the heat setting will be indicated on the
heater display.
The heat boost can be deactivated by
pressing the Sliding Button until the heat
setting "0" is displayed.
Switching Off Individual Heaters
A selected heater can be turned off in 3
different ways:
•
Simultaneous pressing of the right
and left sides of the slider button
•
Reduction of the heat setting
to "0" using the slider button
•
Use of the timer switch-off function for
the corresponding heater.
Timer Function
The control can run a maximum of 4 heater-
assigned timers and 1 minute minder
timer (which is not assigned to a heater)
simultaneously. The timers can only be
used in B-Mode. A heater timer can only
be assigned to an active heater which has
been set to a level between 1 and 9. The
minute minder timer is independent of any
heater.
In order to use both functions, the timer
function must be activated using the
Activate/Deactivate Timer button
Pressing
for the fist time after activating
the heaters will control the minute minder
timer (no Cooking Zone Indicator will be
flashing, they are all on or off).
Pressing
timer to one of the activated heaters. The
Cooking Zone Indicator will flash.
Pressing
timer in a clockwise direction to the next
active heater, and so on.
Minute Minder Timer
The minute minder timer can be operated
by pressing
activated or not, and is selected only when
all Cooking Zone Indicators are either on or
off, i.e. none will be flashing.
The Timer Display will show "00" to
indicate the timer is active. The decimal
point on the Timer Display indicates that
the timer value.
The minute minder timer will begin counting
down once it has been set, it will not stop
if the appliance is switched off or if the Key
Lock function is activated.
Once it has reached zero, "00" will be
displayed on the Timer Display and the
buzzer will sound. Press any button to stop
the buzzer sounding.
Heater Timer
Heater Timers can only be set when a
heater has been activated, i.e. a heater
level must be set between 1 and 9.
Pressing
minder timer, pressing
the timer to an activated heater. This will
be indicated by the corresponding Cooking
Zone Indicator flashing.
Pressing
the first heater timer, will activate the timer
for the next active heater in a clockwise
direction. This will be indicated by its
corresponding Cooking Zone Indicator
flashing. Pressing
allow the timer to be set a value for the
active heater.
The timer for the heater that was set first
will be indicated by the illumination of its
corresponding Cooking Zone Indicator.
Pressing
be assigned to the other activated heaters.
The Timer Display will change, 10 seconds
after the last operation, to the timer that will
run out next. The number of timers that are
running will be indicated by the number of
.
illuminated Cooking Zone Indicators.
The timer values for the heater timer and
minute minder timer can be displayed by
EN - 14
for a second time will assign a
again, will assign the next
, whether a heater has been
can now be used to set
once will activate the minute
again will assign
for a third time, after setting
again will allow more timers to
will
Publicité
