Teleco TXI Serie Guide Rapide page 3

ENGLISH
WALL MOUNTED MANUAL TRANSMITTER TXI SERIES
PRODUCT DESCRIPTION
UHF band transmitter with PPL controlled carrier frequency. This type of transmitter is used for
controlling devices for domestic use, automatic openings, ON-OFF light control, dimming, etc. This
appliance transmits a rolling code type signal to guarantee maximum secrecy. The transmitter code
can be stored in the receiver directly via the latter or via radio from the transmitter. With the second
possibility you can add new transmitters to an existing system without having to touch the receiver.
This can be done directly by the end user (the installer's help is not required). The code is stored in
the receiver's EEPROM memory that retains it even if power is cut temporarily.
USE INFORMATIONS
The trasmitter is in no way protected against interference from other telecommunication equipment
or systems (e.g. authorised radio systems working on the same frequency range). If you are having
problems with its range of action, fix the transmitter up high. Change the battery if necessary.
GENERAL SAFETY RULES
• Keep the transmitter out of the reach of children or animals.
• Do not use the manual transmitter in places or where systems are sensitive to radio emissions
(e.g. airports, hospitals).
• Do not keep or use the manual transmitter in places that are damp, where there is steam, high air
humidity, dust or where it is exposed to the direct rays of the sun or similar environmental conditions.
• Store the transmitter in stable conditions; the fall can cause damage or a reduction in the range
of action.
WARNINGS
KEEP OUT OF REACH OF CHILDREN.
DO NOT INGEST THE BATTERY, DANGER OF CHEMICAL BURNS.
• This product contains a coin/button cell battery.
If the coin/button battery is swallowed, it can cause severe internal burns
in as little as 2 hours and lead to death.
• Keep new and used batteries out of the reach of children.
• If the battery compartment does not close securely, stop using the
product and keep it out of the reach of children.
• If you suspect that batteries have been swallowed or inserted into other
body orifices, seek immediate medical attention.
WARNINGS
EXPLOSION HAZARD IF THE BATTERY IS SUBSTITUTED INCORRECTLY.
• Replace the battery with a CR2430 type battery only.
• Always wrap the battery up, both when it is being stored and when it is being disposed of. The
battery should not come into contact with other metal objects as it could cause the battery to run
down, catch fire or be damaged.
• Dispose of damaged or finished batteries immediately in compliance with the law.
To this end, contact the authorities for safeguarding the environment or the centre
for disposing of waste materials in your area. Do not throw the battery away with
household rubbish.
TRANSMITTER KEYS
The transmitter is equipped with 1 to 7 keys, from CH1 to CH7 depending on the model.
Inside there is also a hidden P3 key (see figure 1) used for programming the receiver.
: Refer to the text in the instructions
EXAMPLES OF COMMAND FUNCTION
TVTXIxxxBB01 White TVTXIxxxBB01G White
TVTXIxxxNN01 Black TVTXIxxxNN01G Black
CH1
CH1
TVTXIxxxBB02 White
TVTXIxxxBB02G White
TVTXIxxxNN02 Black
TVTXIxxxNN02G Black
CH1 CH2
CH1
C
CH2
C
TVTXIxxxBB03 White
TVTXIxxxNN03 Black
Open/Stop/Close
Open ▲
CH5
Stop ■
CH6
► ► ► ► ► ► ► ► ►
Chiude ▼
CH7
The 6-key transmitters function as
two separate 3-key transmitters.
They have in common the memory
key P3. Before using the P3 key,
press a transmitter channel that
TVTXIxxxBB03L White
TVTXIxxxNN03L Black you want to associate.
► ► ► ► ► ► ► ► ►
Dim +
▲
CH5
Dim - ▼ Dimmer
CH6
■
ON/OFF CH7
TVTXIxxxBB07 White
TVTXIxxxNN07 Black
▲
100% CH1 CH5 Dim +
▼ Dim -
75% CH2 CH6
Dimmer
50% CH3
■
25% CH4 CH7
ON/OFF
TVTXIxxxBB07 White
TVTXIxxxNN07 Black
R / C Color
CH1 CH5
Speed 1
Selection 1/2
G / Y
CH2 CH6 CICLO Dimmer RGB
Speed 2
B / M
CH3
Speed 3
WW / CW
OFF
CH4 CH7
Pause/Play
CHANGING THE BATTERY
Single key / Pair keys
• ON
• OFF
1. Lift the corner of the plate by levering with a screwdriver in the appropriate slot.
• ON/OFF/Dim
2. Open the flap.
• ON/Color change/OFF
3. Remove the dead battery and insert a new one.
• Open/Stop - Close/Stop
Pay attention to the correct polarity (+/-)!
• etc.
4. Close the flap.
5. Press the corner of the plate until you hear a CLICK.
WALL MOUNTING
TVTXIxxxBB04 White
The transmitter can be fixed to the wall in two ways: by screws or by adhesive.
TVTXIxxxNN04 Black
GUARANTEE
CH1
C
The guarantee complies with the law. If the guarantee has to be used please refer to
CH2
the specialized retailer. The right to the guarantee is applicable only for the country
CH3
in which the manual transmitter was purchased. The batteries are not covered by
C
CH4 the guarantee.
MEMORIZE,DELETE,COPY A TRANSMITTER
Follow the receiver's instructions.
TVTXIxxxBB06 White
UE CONFORMITY DECLARATION
TVTXIxxxNN06 Black
The manufacturer, Teleco Automation s.r.l, declares that the type of radio equipment is
compliant with Directive 2014/53 / EU. The full text of the EU compliance declaration is
available at the following Internet address: www.telecoautomation.com/ce
Open CH5 ▲ CH5 Open
Stop CH6 ■ CH6
Stop
USA & CANADA CONFORMITY DECLARATION
Chiude ▼ CH7
CH7 Chiude
The manufacturer, Teleco Automation SRL declares that the above mentioned articles
satisfy the following technical regulations applicable:
Trasmettitore Trasmettitore
- FCC PART 15 (Federal Communications Commission)(ID FCC: P59TVTXI916S)
1 2
- IC (Industry Canada) RSS-102 (IC:11242A-TVTXI916S)
TVTXIxxxBB06L White
WARNINGS: Compliance with FCC (Part15) rules:
TVTXIxxxNN06L Black
1 - This device may not cause harmful interference.
2 - This device must accept any interference received, including interference that may
Dim +
Dim + CH5 ▲ CH5 cause undesired operation.
3 - Changes or modifications to this unit not expressly approved by the party
Dim -
Dim - CH6 ▼ CH6
responsible for compliance could void the user's authority to operate the equipment.
ON/OFF CH7 ■ CH7 ON/OFF
Transmitter Transmitter
1 2 TECHNICAL SPECIFICATIONS
Carrier frequency
TVTXIxxxBB07 White
TVTXIxxxNN07 Black
ERP
▲
CH1 CH5 Dim +
C Power supply
▼ Dim -
CH2 CH6
Consumption when transmitting
Working temperature
CH3
C
■
CH4 CH7
ON/OFF
The transmitters are coded directly by the manufacturer with a different code for
each transmitter.
On ALL transmitters, the keys
can also be stored as single-key
commands. In Pairs, on the other
hand, only where represented
with the symbol C. Single / Pair
memorizations are possible only
if indicated among the receiver
In the view of a constant development of their products, the manufacturer reserves
memorizations.
the right for changing technical data and features without prior notice.
see figure 2
(see figure 3 )
(TVTXI868xxxx)
(TVTXI916Sxxx)
TVTXI868xxxx 868.3 MHz
TVTXI916Sxxx 916 MHz
5 dBm
3V±10% (lithium battery CR2430)
10 mA
-10° +55°C