Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
PLEASE READ THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE
REFERENCE! IF YOU DO NOT UNDERSTAND THE INSTRUCTIONS, OR DO NOT
FEEL THAT YOU CAN FOLLOW THEM SAFELY, CONTACT A QUALIFIED
CONTRACTOR. THE WARRANTY WILL BE HONOURED IF ACCOMPANIED BY AN
ORIGINAL SALES RECEIPT, AND ONLY IF THE INSTRUCTIONS HAVE BEEN
FOLLOWED EXACTLY.
• The EM-FT2B is designed to mount a flat panel onto a vertical wall. Hardware for mounting to a
wood stud is included. For mounting to any other surface, contact a qualified contractor.
• The wall or mounting surface must be capable of supporting the combined weight of the mount
and the flat panel, otherwise the structure must be reinforced.
• Safety gear and proper tools must be used. Failure to use safety gear can result in property
damage, serious injury, or death.
• Follow all instructions and recommendations regarding adequate ventilation and suitable
locations for mounting your flat panel. Consult the owner's manual for your flat panel for more
information.
• This product will hold flat panels up to 46 inches and weighing up to 100 lbs.
• VESA 400mm x 400mm
• Two people are recommended for installation
Tools Required
•
Phillips head screw driver
•
Rachet or driver with 13mm (1/2") socket
•
Electric or portable drill
•
6mm (1/4") drill bit and stud finder for drywall installation
•
10mm (3/8") masonry bits for concrete installation
(A) M8 x 63 Lag Bolt (x4)
(E) M4 x 20 Bolt (x4)
(I) M8 x 30 Bolt (x4)
1
All manuals and user guides at all-guides.com
Instructions
(Ref) Item (Qty)
(B) Lag Bolt Washer (x4)
(F) M6 x 12 Bolt (x4)
(J) M6 Washer (x4)
(K) Spacer (x8)
(C) Concrete Anchor (x4)
(D) M4 x 12 Bolt (x4)
(G) M6 x 30 Bolt (x4)
(H) M8 x 12 Bolt (x4)
(L) Tilt Adjustment Knob (x2)
EM-FT2B
(M) M4 x 10 Screw (x2)
FT2B.ME.062011.IM
Publicité
Manuels Connexes pour Evermount EM-FT2B
Sommaire des Matières pour Evermount EM-FT2B
- Page 1 ORIGINAL SALES RECEIPT, AND ONLY IF THE INSTRUCTIONS HAVE BEEN FOLLOWED EXACTLY. • The EM-FT2B is designed to mount a flat panel onto a vertical wall. Hardware for mounting to a wood stud is included. For mounting to any other surface, contact a qualified contractor.
- Page 2 All manuals and user guides at all-guides.com Part 1A - Mounting the wall plate to dry wall 1. Use a high quality stud finder to locate two adjacent studs where you wish to install your mount. Mark both edges of each stud to help identify the exact center. NOTE: You must use the center of each stud to avoid cracking or splitting the wood during installation.
- Page 3 All manuals and user guides at all-guides.com Part 2 – Attaching the mount to the flat panel IMPORTANT: Use extra care during this part of the installation. If possible, avoid placing your flat panel facedown as it may damage the viewing surface. NOTE: This mount comes with a selection of different screw diameters and lengths to accommodate a wide variety of flat panel models.
- Page 4 All manuals and user guides at all-guides.com Part 3 – Final Assembly 1. With the help of another person, carefully lift your flat panel and place it on the wall plate. Do not release until the mount arms are securely hooked onto the wall plate. 2.
- Page 5 ORIGINAL ET UNIQUEMENT SI LES INSTRUCTIONS ONT ÉTÉ SUIVIES À LA LETTRE. • Le EM-FT2B est conçu pour fixer un écran plat sur un mur vertical. Le matériel servant au montage sur montant de bois est inclus. Pour le montage sur toute autre surface, veuillez communiquer avec un technicien qualifié.
- Page 6 All manuals and user guides at all-guides.com Partie 1A – Montage de la plaque murale sur cloison sèche 1. Utilisez un détecteur de montants de haute qualité pour repérer deux montants adjacents à l'endroit où vous souhaitez installer votre support. Marquez les deux bords de chaque montant afin d'en identifier précisément le centre.
- Page 7 All manuals and user guides at all-guides.com Partie 2 – Fixation du support à l'écran plat IMPORTANT : Soyez très prudent lors de cette étape de l’installation. Évitez autant que possible de placer votre écran face vers le bas, cela pouvant endommager sa surface. REMARQUE : Ce support est livré...
- Page 8 All manuals and user guides at all-guides.com Partie 3 – Assemblage final 1. Avec l’aide d’une autre personne, soulevez votre écran avec précaution et placez-le sur la plaque murale. Ne relâchez pas l'écran tant que les bras de montage ne sont pas bien accrochés sur le mur. 2.