R+M Suttner WEEDDEVIL Instructions De Service page 6

User Manual of weeddevil device for weed control
weeddevil professional surface cleaner for sustainable weed control
product code: 200 097 700
Scope of supply
This weeddevil is delivered without nozzles. 4 nozzles 1/4" M with 65° spray angle are required.
Cleaning and maintenance
Please do not clean this device by means of direct high pressure jets as it is suffi cient to wipe it clean with a cloth or sponge and
tap water. Please use a customary cleaning agent. It is absolutely necessary to regularly remove soil, dirt and rest of weed from the
wheels and to clear the nozzles from blockages. The weeddevil must be protected against frost!
Assembly
1. POS.1 Connect stop nut 1/4 „-f with POS.2 nipple 1/4"-m and tighten with the
appropriate tool until it stops
2. TSubsequently screw POS.3 spring washer with POS.4 M6x10 hexagon bolt
through the holes in POS.5 sheet to the POS.6 housing, but do not tighten yet.
3. POS.1 Tighten the stop nut POS.1 with POS.2 nipple 1/4"-m, which creates a
tight connection.
4. Now screw POS.4 fi rmly to the housing POS.6.
Warning
Attention - risk of burns! The spraying bar must be mounted so that it is always directed downwards,
see fi g. 1. The hot water jet must not be directed at animals or persons. Do not ever grab into the
water jet!
Putting into operation
Please switch on your hot water high pressure cleaner and pull the trigger of your high pressure gun.
Please wait until hot water comes out (heating time of the high pressure cleaner must be noticed).
The weeddevil needs to be moved slowly over the weed and this process may be repeated a few times,
if required. It is very important that as little steam as possible comes out and that the hot water is
applied by very little pressure.
Possible malfunction
Malfunction: The device does not work with full power.
Reason:
The nozzles are possibly blocked.
Remedy: Please screw the nozzles out of the spraying bar and clean them by means of a special
tip cleaner (fi g. 2). Afterwards the pipe with handle and the spraying bar should be
rinsed under clear water. Please reassemble your weeddevil and it should work as
good as before. If the weeddevil does not work smoothly again it is time to check the
high pressure cleaner then. Therefore, please carefully read the user manual of your
high pressure cleaner or contact the distributor or manufacturer of the high pressure
cleaner.
page 2, vers. 2019-10
All manuals and user guides at all-guides.com
Pos.
1
2
3
4
5
6
7
5. Please screw 4 nozzles (4 nozzles 1/4" M with 65°
spray angle are required) into the nozzle spray bar.
Please plug your spray gun into the connection 1/4" F
at the pipe with handle and screw it tight.
6. The high pressure cleaner can now be connected.
Artikelnummer Benennung
070003191 Griffrohr ø16x3x1.100 mm gebogen
57049 Doppelnippel 1/4" AG Edelstahl
200009525 Halbschale ST-9 mit seitlichem Handgriff
582039 Überwurfverschraubung 1/4" Edelstal
040003206 Gehäuse weeddevil 400 mm
200097401 Repair-Kit Düsenaufnahme weeddevil
200097402 Repair-Kit Rad/Aufnahme/Schrauben/O-Ring
weeddevil
POS. 4
POS. 5 POS. 3
POS. 6
POS. 1
POS. 2
g. 1
Recommendation from R+M /
Suttner: tip cleaner
High speed steel (HSS)
with aluminium shaft.
Length 42 mm
R+M Nr.
diameter
200 049 042 0.5
www.rm-suttner.com
g. 2