Télécharger Imprimer la page

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

IMPORTANT INSTRUCTIONS -
ESF Series (Single Speed)
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!
electric shock and injury to person, including the following:
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK
AND INJURY TO PERSON, OBSERVE THE FOLLOWING:
a) Use this unit only in the manner intended by the manufacturer. If
you have questions, contact the manufacturer.
b) Before servicing or cleaning the unit, switch power off at service
panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK
AND INJURY TO PERSON, OBSERVE THE FOLLOWING:
a) Installation work and electrical wiring must be done by qualified
person(s) in accordance with all applicable codes and standards,
including fire-related construction.
b) Sufficient air is needed for proper combustion and exhausting
of gases through the flue (chimney) of fuel burning equipment
to prevent back drafting. Follow the heating equipment
manufacturer's guideline and safety standards such as those
published by the National Fire Protection Association (NFPA)
and the American Society for Heating, Refrigeration, and Air
Conditioning Engineers (ASHRAE), and the local code authorities.
c) When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
6728048 Rev. D 5-14
All manuals and user guides at all-guides.com
OPERATING MANUAL
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
GENERAL SAFETY INFORMATION
When using electrical appliances, basic precautions
should always be followed to reduce the risk of fire,
SAVE THESE INSTRUCTIONS
d) Ducted fans must always be vented to the outdoors.
e) If this unit is to be installed over a tub or shower, it must be
marked as appropriate for the application and be connected to a
GFCI (Ground Fault Circuit Interrupter) - protected branch circuit.
f) This unit must be grounded.
g) To avoid motor bearing damage and noisy and/or unbalanced
impellers, keep drywall spray, construction dust, etc. off power unit.
h) Suitable for use with electronic speed control device.
CAUTION:
USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS AND
VAPORS.
i) Do not install in a ceiling with thermal insulation value greater
than R40.
WARNING:
i) Read all instructions before installing or using exhaust fan.
www.airkinglimited.com
Exhaust Fan with Light
FOR GENERAL VENTILATING USE ONLY. DO NOT
DO NOT USE IN KITCHENS.
1 of 12

Publicité

loading

Sommaire des Matières pour AirKing ESF Serie

  • Page 1 All manuals and user guides at all-guides.com IMPORTANT INSTRUCTIONS - OPERATING MANUAL ESF Series (Single Speed) Exhaust Fan with Light READ AND SAVE THESE INSTRUCTIONS READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
  • Page 2 All manuals and user guides at all-guides.com INSTALLATION INSTRUCTIONS SECTION 4 Ducting CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL BEFORE CAUTION: STARTING INSTALLATION. ALL DUCTING MUST COMPLY WITH LOCAL AND NATIONAL BUILDING CODES. SECTION 1 Connect the ducting to the fan’s duct collar (Figure 4). Secure in place using tape Preparing the Exhaust Fan or screw clamp.
  • Page 3 All manuals and user guides at all-guides.com Wiring the Lights: Using a properly grounded standard duplex toggle switch (such as Leviton 5224-2W, not included) connect the black wire from the supply to one side of the top and bottom switch. Connect the red wire (light) from the fan housing to the other side of the top switch and connect the purple wire (night light) from the fan housing to the other side of the bottom switch.
  • Page 4 All manuals and user guides at all-guides.com NOTE: This is a minimum time that the fan will operate. If the room is occupied longer, the fan will continue to run until the room is vacated and the occupancy time delay has elapsed. Screws 2b.
  • Page 5 All manuals and user guides at all-guides.com Troubleshooting Guide Trouble Probable Cause Suggested Remedy 1. Fan does not operate when the switch is on. A fuse may be blown or a circuit tripped. Replace fuse or reset circuit breaker. Connector plug from motor is not plugged in. 1b. Turn off power to unit. Remove Grill and plug motor into receptacle in housing.
  • Page 6 All manuals and user guides at all-guides.com REPLACEMENT PARTS DIAGRAM All Models Qty. Description Replacement Part # Mounting Rails 5S1299002 6” Metal Collar Assembly 5S5299100 Specific to Models ESF80SG, ESF130SG Grill Springs 5S1202046 Qty. Description Replacement Part # Ceiling Flange 5S1239024 Grill Assembly 5S1239118...
  • Page 7 All manuals and user guides at all-guides.com INSTRUCTIONS IMPORTANTES – MODE D’EMPLOI Ventilateur combiner, comprend Série ESF (seule vitesse ) lumière et ventilation LIRE ET CONSERVER CES INSTRUCTIONS LIRE SOIGNEUSEMENT AVANT DE TENTER D’ASSEMBLER, INSTALLER, OPÉRER OU DE RÉPARER LE PRODUIT DÉCRIT. PROTÉGEZ VOUS-MÊME ET LES AUTRES EN OBSERVANT TOUTE L’INFORMATION DE SÉCURITÉ.
  • Page 8 All manuals and user guides at all-guides.com INSTRUCTIONS D’INSTALLATION SECTION 4 Conduits ATTENTION : VOUS ASSURER QUE L’ALIMENTATION EST COUPÉE AU ATTENTION : PANNEAU DE SERVICE AVANT DE COMMENCER L’INSTALLATION. TOUS LES CONDUITS DOIVENT ÊTRE CONFORMES AUX CODES DU BÂTIMENT LOCAUX ET NATIONAUX. SECTION 1 Raccorder le conduit au collet de conduit du ventilateur (Figure 4).
  • Page 9 All manuals and user guides at all-guides.com REMARQUE : Le fil jaune peut contenir un écrou de fil à sertir qui devra être coupé et le fil dénudé. Câblage des lumières : à l’aide d’un interrupteur à bascule duplex standard, proprement mis à...
  • Page 10 All manuals and user guides at all-guides.com 2a Réglage du temps minimum de fonctionnement. Ceci définit la durée minimale de Installez la bride de montage au plafond pour couvrir tous les espaces qui existent entre le boîtier et le plafond fini. Retirer les deux vis qui relient la bride de montage au boîtier. fonctionnement à...
  • Page 11 All manuals and user guides at all-guides.com ATTENTION : PERMETTRE À L’AMPOULE DE SE REFROIDIR AVANT DE LA REPLACER. Remplacement de l’ampoule : débrancher l’alimentation de l’unité. Ouvrez l’objectif de lumière sur la grille en poussant dans l’objectif pour lui permettre de s’ouvrir. Ampoule Fluorescente : Pour enlever l’ampoule, basculer vers l’extérieur de la douille et en tirant pour l’extraire de sa base.
  • Page 12 All manuals and user guides at all-guides.com DIAGRAMME DES PIÈCES DE REMPLACEMENT Tous les modèles # de pièce Qté. Description de remplacement Traverses de Montage 5S1299002 Particularités des modèles ESF80SG, ESF130SG Assemblée de collier en métal de 6 po 5S5299100 # de pièce Ressorts de la grille 5S1202046...