Publicité
Liens rapides
Model/Modelo/Modèle
551-DST & 751-DST
Series/Series/Seria
Write purchased model number here.
Escriba aquí el número del modelo comprado.
Inscrivez le numéro de modèle ici.
For easy installation of your Delta
faucet you will need:
READ ALL the instructions completely
before beginning.
READ ALL warnings, care, and maintenance
information.
Para instalación fácil de su llave Delta
usted necesitará:
LEER TODAS las instrucciones completamente
antes de empezar.
LEER TODOS los avisos, cuidados, e
información de mantenimiento.
Pour installer votre robinet Delta
facilement, vous devez:
LIRE TOUTES les instructions avant de débuter;
LIRE TOUS les avertissements ainsi que toutes
les instructions de nettoyage et d'entretien;
www.deltafaucet.com
61836
SINGLE HANDLE LAVATORY
CENTERSET AND VESSEL FAUCETS
LLAVES MONOCONTROL DE MONTURA
DE CENTRO PARA LAVAMANOS
ROBINETS À ENTRAXE COURT À
UNE POIGNÉE
You may need/Usted puede necesitar/
Articles dont vous pouvez avoir besoin:
1/8"
61836
1
1/8"
2/3/12
Rev. D
Publicité
Manuels Connexes pour Delta 751-DST Serie
Sommaire des Matières pour Delta 751-DST Serie
- Page 1 READ ALL the instructions completely before beginning. READ ALL warnings, care, and maintenance information. 1/8" 1/8" Para instalación fácil de su llave Delta usted necesitará: LEER TODAS las instrucciones completamente antes de empezar. LEER TODOS los avisos, cuidados, e información de mantenimiento.
- Page 2 MAKE ANY OTHER WARRANTY OF ANY KIND, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY. Delta will replace, FREE OF CHARGE, during the warranty period, any part or finish that proves defective in material and/or workmanship under normal installation, use & service. Replacement This warranty excludes all industrial, commercial &...
- Page 3 Model 551-DST / Modelo 551-DST / Modèle 551-DST For Three Hole Installation: For Single Hole Installation: Slide escutcheon (1) and spacer with round gasket (2) up over Slide single hole escutcheon (1) and spacer with round gasket tubes and mounting stud. Position spacer and gasket under (2) up over tubes and mounting stud.
- Page 4 Model 751-DST / Modelo 751-DST / Modèle 751-DST For Vessel Faucet Installation: Slide escutcheon (1) and spacer (2) with gasket (3) up over tubes Place metal bracket (4) over mounting stud (5) under sink. Secure and mounting stud. Position faucet assembly on sink. Option: If with mounting nut / wrench (6).
- Page 5 Faucet fittings (1) are 3/8" compression, with allows a leak-free joint to be created. Delta is not careful not to cut the tube too short. ends colored red for hot and blue for cold. Loop responsible for tubing that is cut too short or cut ●...
- Page 6 Incorrect Installation Correct method Instalación Incorrecta Método Correcto Installation Incorrecte Bonne méthode Do not install sleeve Ensure cut is straight. upside down. No instale la manga Asegúrese que el Custom Fit Connections - Plastic Sleeve Installation Instructions boca abajo. corte esté recto. 1.
- Page 7 Metal Pop-Up Remove stopper (1) and flange (2). Apply silicone to underside of flange (1). Insert Remove pivot nut (1). Install horizontal body (2) into sink. Screw flange (1) into body (2). rod (2) and stopper (3) as removable Screw nut (1) all the way down. Push (4) or non-removable (5).
- Page 8 Remove aerator (1) using supplied wrench (2) and move faucet Check all connections at arrows for leaks. Retighten if necessary, handle (3) to the full on mixed position. Turn on hot and cold water but do not overtighten. supplies (4) and flush water lines for one minute. Important: This flushes away any debris that could cause damage to internal parts.
- Page 9 Setting The Handle Limit Stop (Optional) This faucet includes an integrated handle limit stop that has two this handle limit stop will not always prevent scalding because it positions. Position 1, to the left, allows full handle motion (the full range does not compensate for incoming pressure or sudden water between “all cold”...
- Page 10 1/8" Maintenance Cleaning and Care If faucet exhibits very low flow: Care should be given to the cleaning of this reinstalling parts, make sure bonnet nut (4) is A. Remove and clean aerator (1) with supplied tightened securely with a wrench.* product.
- Page 11 Model / Modelo / Modèle 551-DST RP61837 RP61838▲ Button / Botón / Bouton Handle, Button & Set Screw RP50953 Manija, Botón l y Tornillo de Ajuste ▲Specify Finish Set Screw Manette, Bouton et Vis de Calage Tornillo de Ajuste Especifíque el Acabado Vis de calage Précisez le Fini RP54972▲...
- Page 12 Model / Modelo / Modèle 751-DST RP61837 Button / Botón / Bouton RP50953 RP61838▲ Set Screw Handle, Button & Set Screw Tornillo de Ajuste Manija, Botón l y Tornillo de Ajuste Vis de calage Manette, Bouton et Vis de Calage RP54972▲...