Renkforce 1369187 Mode D'emploi page 3

Operating instructions
Siren dummy
Item no. 1369187
Intended use
This product is a siren dummy that resembles a functional alarm with
robust metal housing. It is suitable for indoor and outdoor installation
using the supplied wall plugs and screws. The power supply requires
2 AA batteries (not included).
For safety and approval purposes (CE), you must not rebuild and/or
modify this product. If you use the product for purposes other than
those described above, the product may be damaged. In addition,
improper use can cause hazards such as short circuiting, fire,
electric shock etc. Read the instructions carefully and keep them.
Make this product available to third parties only together with its
operating instructions.
This product complies with the statutory national and European
requirements. All company names and product names are trademarks
of their respective owners. All rights reserved.
Delivery content
• Siren dummy
• 2 × screws
• 2 × dowels
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially
observe the safety information. If you do not follow the safety
instructions and information on proper handling in this
manual, we assume no liability for any resulting personal
injury or damage to property. Such cases will invalidate the
warranty/guarantee.
• The product is not a toy. Keep it out of the reach of children
and pets.
• Do not leave packaging material lying around carelessly.
These may become dangerous playing material for children.
• Protect the product from extreme temperatures, strong
jolts, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take
it out of operation and protect it from any accidental use.
Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient
conditions or
- has been subjected to any serious transport-related
stresses.
All manuals and user guides at all-guides.com
Operation
a) Inserting / replacing batteries
• Remove the dummy light chamber from the metal housing (fig. 1).
• Remove the battery compartment cover (fig. 2).
• Insert 2 AA batteries (not included), heeding correct polarity.
• Install the battery compartment cover.
• Fix the light chamber back to the metal housing. The red LED should
b) Mounting the product
• Select a stable, vertical surface (e.g. the wall of buildings).
• Mount the product in such a way that the red LED is not blocked.
• Mark the position of the mounting holes on the mounting surface,
• Drill the two mounting holes into the surface. Heed the length and
• Please handle the product carefully. Jolts, impacts or a fall
even from a low height can damage the product.
• Never point a garden hose at the product.
• The product may not be mounted in or under water.
• Correct polarity must be observed while inserting the
(rechargeable) batteries.
• (Rechargeable) batteries should be removed from
the product if it is not used for a long period of time to
avoid damage through leaking. Leaking or damaged
(rechargeable) batteries might cause acid burns when in
contact with skin, therefore use suitable protective gloves
to handle corrupted (rechargeable) batteries.
• (Rechargeable) batteries must be kept out of reach of
children. Do not leave (rechargeable) batteries lying
around, as there is risk, that children or pets swallow them.
• All (rechargeable) batteries should be replaced at the
same time. Mixing old and new (rechargeable) batteries in
the product can lead to (rechargeable) battery leakage and
product damage.
• (Rechargeable) batteries must not be dismantled,
short-circuited or thrown into fire. Never recharge non-
rechargeable batteries. There is a risk of explosion!
• Maintenance, modifications and repairs are to be
performed exclusively by an expert or at a qualified shop.
• Consult an expert when in doubt about operation, safety or
connection of the device.
• If you have questions which remain unanswered by these
operating instructions, contact our technical support
service or other technical personnel.
Observe the polarity markings in the battery compartment.
face the side with mounting holes on the metal housing.
fig. 1
Replace the batteries when display operation weakens
significantly.
for example using a pencil. The distance between the two holes is
10 cm.
diameter of the wall plugs while drilling.
fig. 2