Westin 22-1785 Consignes

AUTOMOTIVE PRODUCTS, INC.
MOUNT KIT
EQUIPO DE MONTAJE
TROUSSE DE MONTAGE
22-1785
CHROME/CROMADO/CHROME
22-0060, 22-5060
BLACK/NEGRO/NOIR
22-0065, 22-5065
ITEM QTY
1,2 2 STEP BAR, PASSENGER (1) AND DRIVER (2)
3,4 2 FRONT BRACKET, PASSENGER (3) AND DRIVER (4)
5,6 2 REAR BRACKET, PASSENGER (5) AND DRIVER (6)
7 2 MOUNT BRACE
8,9 4 MOUNT PLATE, PASSENGER (8) AND DRIVER (9)
10 10 3/8-16 X 1.25" HEX HEAD BOLT
11 14 3/8" FLAT WASHER
12 12 3/8" LOCK WASHER
13 4 3/8-16 HEX NUT
14 4 M6 BOLT PLATE (INCLUDED WITH STEP TUBES)
15 16 M6 FLAT WASHER (INCLUDED WITH STEP TUBES)
16 16 M6 LOCK NUT (INCLUDED WITH STEP TUBES)
17 2 BOLT PLATE
1,2 2 ESTRIBOS, ACOMPAÑANTE (1) Y CONDUCTOR (2)
3,4 2 SOPORTES DELANTERAS, ACOMPAÑANTE (3) Y CONDUCTOR (4)
5,6 2 SOPORTES TRASERAS, ACOMPAÑANTE (5) Y CONDUCTOR (6)
7 2 PIEZA DE SUJECIÓN DEL SOPORTE
8,9 4 PLACA DE MONTAJE, ACOMPAÑANTE (8) Y CONDUCTOR (9)
10 10 PERNOS CON CABEZA HEXAGONAL DE 3/8-16 X 1,25"
11 14 ARANDELAS PLANAS DE 3/8"
12 12 ARANDELAS DE PRESIÓN DE 3/8"
13 4 TUERCAS HEXAGONALES DE 3/8-16
14 4 TORNILLO M6 PLACAS (INCLUIDO CON TUBOS STEP)
15 16 M6 ARANDELAS PLANAS (INCLUIDO CON TUBOS DE PASO)
16 16 LAS TUERCAS M6 (INCLUIDO CON TUBOS DE PASO)
17 2 BASE DE MONTAJE
1,2 2 MARCHE-PIEDS, PASSAGER (1) ET CONDUCTEUR (2)
3,4 2 SUPPORTS AVANT, PASSAGER (3) ET CONDUCTEUR (4)
5,6 2 SUPPORTS ARRIERE, PASSAGER (5) ET CONDUCTEUR (6)
7 2 RENFORTS POUR SUPPORTS
8,9 4 PLAQUE DE MONTAGE, PASSAGER (8) ET CONDUCTEUR (9)
10 10 BOULON A TETE HEXAGONALE DE 3/8-16 X 1,25 PO
11 14 RONDELLE PLATE DE 3/8 PO
12 12 RONDELLE A FREIM DE 3/8 PO
13 4 ÉCROUS HEXAGONAUX 3/8-16
14 4 BOULON M6 PLAQUES (INCLUS AVEC TUBES STEP)
15 16 M6 RONDELLES PLATES (INCLUS AVEC TUBES STEP)
16 16 NUTS M6 LOCK (INCLUS AVEC TUBES STEP)
17 2 PLAQUES DE BOULON
STEP 1. Remove the contents from box and check for damage. Verify all parts are present. Read instructions completely before beginning.
STEP 2. Determine passenger and driver brackets.
STEP 3. Locate rear mount holes (one slot and one hole) on underside of the rocker panel below passenger rear door. Insert mount plate into slot so holes
of mount plate line up with mount holes on vehicle. High side of mount plate should face up. SEE FIGURE 1.
STEP 4. Attach rear bracket to vehicle rocker panel using 3/8" fasteners as shown. Hand tighten. SEE FIGURE 1.
STEP 5. Locate front mount holes (one slot and one hole) on bottom of unibody rail below front door. Insert mount plate into slot so holes of mount plate
line up with mount holes on vehicle. High side of mount plate should face up. SEE FIGURE 1.
STEP 6. Attach front bracket to vehicle rocker panel using 3/8" fasteners as shown. Hand tighten. SEE FIGURE 1.
STEP 7. Locate hole for front brace on bottom of unibody rail between front bracket mounting location and rocker panel. Insert bolt plate into hole and
attach short end of brace to bolt plate and long end of brace to front bracket. Secure using 3/8" fasteners. Leave loose. SEE FIGURE
1.NOTE:Hole in unibody on passenger side for front brace may be to small to insert bolt plate. Enlarging the whole may be
required
All manuals and user guides at all-guides.com
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 2008 FORD ESCAPE/MAZDA TRIBUTE/MERCURY MARINER
APLICACIÓN: FORD ESCAPE/MAZDA TRIBUTE
APPLICATION: FORD ESCAPE/MAZDA TRIBUTE/MERCURY MARINER 2008
2
CONTENTS - CONTENIDO
3
1
4
- CONTENU
WO:
/MERCURY MARINER , MOD. 2008
7
5
8
6
TOOLS - HERRAMIENTA
9/16" SOCKET
13MM SOCKET
9/16" WRENCH
RATCHET
TORQUE WRENCH
DADO DE 9/16"
DADO DE 13MM
LLAVE DE TUERCAS DE 9/16"
MANERAL
LLAVE DE TORQUE
DOUILLE 9/16 PO
DOUILLE 13MM
CLE 9/16 PO
CLIQUET
CLEF DE COUPLE
75-0836 REVISION C 2/11/11
9
17
- OUTILS