camry Premium CR 2921 Mode D'emploi page 4

immediately remove the power plug or power adaptor from the socket. If the device is
powered, do not put hands in the water. Have the device checked by the qualified
electrician before using it again.
18. Do not touch the device or power adaptor with wet hands.
19. The device has to be turned off after every use.
20. Do not leave the unit on to the wall outlet or power supply unit unattended.
21. If the device utilises a power adaptor, do not cover it, because this can cause a
dangerous temperature rise and can damage the device. Always connect the power
adaptor cable to the device, and then connect the power adaptor to the power socket.
22. Keep the device out of the reach of children. Using the devices by children must be
supervised by adults.
23. The device is designed only for cutting natural human hair.
24. The cutting blades are very sharp. Be careful during assembly, disassembly and
cleaning. Do not touch the blades moving parts during operation!
25. Do not wash the blades in water.
26. Change the attachments only when the unit is turned off.
27. Use only original accessories.
28. To remove hair from inside the machine, use only the included brush.
29. Do not use the device in the bath.
30. Do not use the device on people who are sleeping.
31. During operation, do not place the device on wet surfaces or clothes.
32. The device is not designed to work with external schedulers or separate remote control
system.
33. Do not insert the trimmer into the nose or ear to a depth greater than 5 mm as this may
cause damage to the nasal mucous membrane or eardrum.
DESCRIPTION OF THE DEVICE
1. Power switch
3. Comb attachment
5. Beards and moustaches attachment
7. Eyebrows trimmer
9. Fine shaving head
11. Charger
BATTERY CHARGING
Before use, charge the battery. To begin charging, connect the power cord to the device and the charger to the 230V ~ 50Hz socket. The
charging icon will lights up (Fig. G). Charging should last a maximum of 6 hours. A fully charged battery is sufficient for 30 minutes of
continuous operation. After charging, remove the charger from the wall socket. When the device is not used for a long time, recharge it at
least once every 6 months to maintain adequate battery capacity. If the battery discharges you can continue cutting using the charger. To
do this, place the charger plug into the socket of device. After 2 minutes you can continue haircut. Chargers plug cable can be also placed
in the base (Fig. A). This allows you to charge the device in a standing position.
USING THE DEVICE
Depending on the needs install the appropriate trimmer or head as shown in Figure F. To remove it follow the drawing E.
To set the desired length using attachments (Fig. B-D) and the slider follow the table.
Trimmer for ears and nose:
Apply trimmer for ears and nose (8). Make sure that the septum and earlobe are clean before using the trimmer. Place the tip of the
trimmer into the nostril or ear to a depth no greater than 5 mm. Gently moving the turned on trimmer remove only hair protruding outside
of the ear or nose
Eyebrows trimmer:
Apply eyebrows trimmer (7). Gently slide the turned on trimmer in place where you want to shorten the eyebrows. Do not approach the
device in the eye area.
Trimmer for beards and mustaches:
Apply trimmer for beards and mustaches (6). To adjust the cutting length you can instal attachment (5) on the trimmer. Move the turned on
trimmer against the direction of hair growth.
Clipper:
Apply clipping head (2). To adjust the cutting length you can instal attachment (3) on the trimmer. By moving the attachment on the head,
you can select the desired haircut length. Start by moving the clipper with the comb attachment against the direction of hair growth. This
step should be performed slowly and at a constant speed.
2. Clipping head
4. The fine cutting length adjustment slider
6. Beards and moustaches trimmer
8. Ears and nose trimmer
10. Base
4