WOODLAND SCENICS JP5701 Instructions

INSTRUCTIONS
BEFORE YOU PROCEED
Read through instruction booklet entirely. Comply with all operating instructions. Failure to follow instructions could result in
damage to the product or personal injury. Do not modify or tamper with any electronic components. Combine products from
the Just Plug Lighting System only, unless otherwise instructed. Save these instructions.
GETTING STARTED
The Just Plug Lighting System is made up of Ports, Plugs and Cables. This simple connection system makes it quick and
easy to light one building or an entire city.
How to Connect a Plug to a Port
Align locking tabs on Plug with front of Light or Expansion Hub. Insert Plug into Hub Port until locking tabs click into place.
(Fig. 1)
How to Remove a Plug from a Port
Grasp top edge of Plug and pull firmly.
LIGHTS & HUB SET / LIGHT HUB
Light Hubs supply power to Just Plug LED Lights.
• To power Light Hub, insert Power Supply (JP5770) plug into POWER IN Port (or use a 16VAC train power pack, Fig. 5).
• Do NOT remove CTRL Port Plug (unless using Auxiliary Switch (JP5725) or connecting to DCC).
• Plug LED Lights (JP5736-JP5749, JP5754, JP5755) into LIGHT Ports. Lights & Hub Set includes two Stick-On Lights. To
secure Lights in building, remove release paper from back of LED and stick on where desired.
• Rotate Dimmer Controls to adjust light brightness (adjusts from very bright to off).
• Use dedicated spaces on front of Hub to label according to your lighting configuration.
• To mount Hub, use included Tape or Screws.
EXPANSION HUB
Connect Light Hubs to Expansion Hub to expand your lighting system.
• To power Expansion Hub, insert Power Supply (JP5770) plug into POWER IN Port (or use a 16VAC train power pack, Fig. 5).
• Do NOT remove CTRL Port Plug (unless using Auxiliary Switch (JP5725) or connecting to DCC).
• Use included Connecting Cables to connect to Light Hubs (Fig. 2), another Expansion Hub (Figs. 3 and 4), train power
pack (Fig. 5) or DCC relay unit (Fig. 6).
• Use dedicated spaces on front of Hub to label according to your lighting
configuration.
• To mount Hub, use included Tape or Screws.
CONNECTING HUBS TOGETHER
Use Connecting Cables (included with Expansion Hub)
Connect Light Hub to Expansion Hub
Insert Connecting Cable Plug into Expansion Hub HUB Port and opposite
Plug into Light Hub POWER IN Port (Fig. 2).
Connect Expansion Hub to Expansion Hub
Insert Connecting Cable Plug into POWER OUT Port on powered
Expansion Hub. Insert opposite Plug into POWER IN Port on add-on
Expansion Hub (Fig. 3). Keep expanding your lighting system (Fig. 4).
Power Hubs from a Train Power Pack
Cut off one Connecting Cable Plug with wire cutters and strip
approximately 1" of wire. Connect bare wires to the accessory terminals
on a 16VAC power pack. Insert Plug on other end of Connecting Cable
into Hub POWER IN Port. (Fig. 5)
Control Just Plug Lighting System with DCC
Cut off one Connecting Cable Plug with wire cutters and strip
approximately 1" of wire. Connect bare wires to DCC relay unit (follow
DCC manufacturer instructions for proper installation of wires). Insert
Plug on other end of Connecting Cable into Hub CTRL Port. (Fig. 6)
Model building item, not a toy! Not intended for children
under 14 years! / Modellbauartikel, kein Spielzeug! / Article de
modélisme. Ceci n'est pas un jouet. / Articolo di modellismo,
LIGHT
non è un giocattolo! / Artículo para modelismo ¡No es un
juguete! / Artigo para modelismo. Este artigo não é um
No.
brinquedo! / Výrobek určený pro modeláře, nejedná se o
hračku! / Modelbouwartikel, geen speelgoed!
4
3
2
CAUTION: Do not look directly into LED lights when in operations.
RoHS Compliant
WOODLAND SCENICS
LIGHTS HUB - JP5701
IN CTRL
POWER LIGHT
LIGHT HUB
No.
DIMMER CONTROLS
1 2 3 4
WOODLAND SCENICS
IN OUT CTRL
POWER HUB
EXPANSION HUB
No.
WOODLAND SCENICS
Combination Package
®
Connecting Cable
Power
Supply
Cable
Connecting Cable
Power
Supply
Cable
1a 1b 1c 1d 2a 2b 2c 2d
1
Fig. 4
Train
Power
Pack
Connecting
Cable
Developed in USA
PO Box 98, Linn Creek, MO 65052 • woodlandscenics.com
Fig. 1
Locking
Tabs
Plug
LIGHT HUB
Power
Supply
Fig. 2
EXPANSION HUB
Fig. 3
Power
Supply
3a 3b 3c 3d 4a 4b 4c 4d
2 3
1 2 3 4
1
Fig. 6
Connecting
Cable
Fig. 5
Made in China G11
Ports
LED
Stick-On
(or Nano)
CTRL
Port
Plug
Light Ports
1a 1b 1c 1d
1
Dimmer Controls
Connecting Cable
CTRL
HUB
Port
Ports
Plug
1 2 3 4
1
5a 5b 5c 5d
4 5
Keep
Expanding
5
2
DCC
Relay Unit
©2014 O CO