Hickory Hardware P5129-14 Instructions D'installation

P5129-14 Instruction BP 1-11-09.FH10 Thu Jan 28 13:37:32 2010
European Cabinet Hinge
P5129-14
For face-frame cabinets
l
Fully concealed
l
Self-closing
l
1 1 / " Overlay
4
º
108 Opening
Nickel Finish
Identifying Number of Hinges Needed
For doors up to 24" wide, weighing up to:
20 lbs., use 2 hinges
l
20 - 40 lbs., use 3 hinges
l
40 - 60 lbs., use 4 hinges
l
60 - 80 lbs., use 5 hinges
l
Note: These recommendations are for doors without
accessory attachments such as mirrors and racks.
What You Will Need
1. Drill, 1 / " (35mm) and / " (2.5 mm) drill bits
3 3
8 32
2. Medium-sized (#2) Phillips screwdriver
3. Carpenters square
4. Tape measure or ruler
5. Pencil
Contents
1 Hinge
1 #10 x / " round-head Phillips screw
3
4
2 #6 x / " flat-head Phillips screws
5
8
Before You Begin
Make sure your cabinet door meets the following
requirements:
1 / " minimum reveal for 3 / " door
4 4
l
/ " minimum reveal for / " door
1 5
8 8
l
1 / " minimum frame width
1
2
l
/ " frame thickness
3
4
l
Door thickness of / " to / " and opening
3 5
4 8
l
angle of 108º
1 / " overlay
1
4
l
Note: Cabinet frame must be made of wood.
face frame width
face
frame
door
reveal
cup drilling
distance
door overlay
© 2010 Belwith Products, LLC
Grandville, Michigan 49418
Ontario, Canada M9W 5B3
Made to Belwith’s specifications in Austria
To Install the Hinge Cup
35 mm
1. Drill a 1 / " (35mm) diameter hole,
3
8
(2.5mm) from edge of door, approximately 2
the top and bottom.
2. Mount hinge to cabinet door, ensuring that hinge arm
is perpendicular to edge of door.
cabinet panel
To Hang the Door
3. Mark hole in center of face frame where center of slot
face frame
in baseplate will be.
4. Drill pilot hole
door panel
5. Fasten hinge arm and door to face frame with #10 x
round-head screw.
Making Adjustments
Note: For best results, use a Phillips screwdriver for all adjustments.
Height Adjustment
To adjust the height of door, loosen screw #1 one turn on
all hinges on door. Raise or lower door to desired position.
Retighten all height-adjustment screws.
Additional Height Adjustment
Loosen screw #3 on all hinges in face frame and adjust
door to desired position. Retighten screws.
Side Adjustment
To adjust the horizontal alignment of the cabinet door,
loosen screw #1 half a turn. Then turn screw #2 until door
is in proper position. You have up to
direction. Retighten #1 screws on all hinges.
Note: Side adjustment can be used to increase or decrease door coverage
by ± / " (± 1.5mm).
1
1 6
Helpful Hints
Do:
Keep hinges as close to top and bottom of
l
cabinet door as possible.
Make sure the hinge arm is mounted 90º to
l
the door.
Check to see that doors do not bind when
l
opening.
Avoid doors which are wider than they are tall.
l
Do a trial mounting to ensure accuracy.
l
Don’t:
Don’t exceed maximum cup drilling distance;
l
door will bind on face frame.
Don’t overuse the adjustments.
l
Don’t overload the door with accessory
l
attachments such as mirrors and racks.
Don’t over-tighten the wood screws.
l
Page 1
Cup Drilling Depth:
( / ")
13 mm 1
2
Cup Drilling Distance:
2.5 mm ( 3 / ")
32
/ " deep, / "
1 3
2 3 2
/ " from
1
2
3 / " deep with 3 / " drill bit.
4 32
3 / "
4
/ " (1.5mm) in each
1
1 6