Page 3
NOMENCLATURE DN 15 - 50 Repère Désignation Matériaux Corps ASTM A351 CF8M Embout Sphère Inox AISI 316 Siège PTFE chargé 3% verre Joint de corps DN15-32 PTFE chargé 15% graphite Joint de corps DN40-50 Inox AISI 304 + graphite Rondelle de glissement PTFE chargé...
Page 4
NOMENCLATURE DN 65 - 100 Repère Désignation Matériaux Corps ASTM A351 CF8M Embout Sphère Inox AISI 316 Siège PTFE chargé 3% verre Joint de corps Inox 304 + graphite Rondelle de glissement PTFE chargé 15% graphite Joint torique Presse étoupe PTFE Fouloir Inox AISI 304...
Page 5
NOMENCLATURE DN 125 - 150 Repère Désignation Matériaux Corps ASTM A351 CF8M Embout Sphère Inox AISI 316 Siège PTFE chargé 3% verre Joint de corps Inox AISI 304 + graphite Rondelle de glissement PTFE chargé 15% graphite Joint torique Presse étoupe PTFE Fouloir Inox AISI 304...
Page 6
DIMENSIONS DN 15 - 50 ( en mm ) : DN 15 - 50 Ref. Ø P 161.2 161.2 161.2 204.5 204.5 204.5 82.7 83.2 88.2 Poids (en Kg) 3.02 3.79 5.74 6.79 9.33 Sferaco 90 rue du Ruisseau 38297 St Quentin Fallavier Tél : 04.74.94.15.90 Fax : 04.74.95.62.08 Internet : www.sferaco.fr E-mail : sferaco@sferaco.fr...
Page 7
DIMENSIONS DN 65 - 100 ( en mm ) : DN 65 - 100 Ref. Ø P Poids (en Kg) 15.2 19.58 27.36 Sferaco 90 rue du Ruisseau 38297 St Quentin Fallavier Tél : 04.74.94.15.90 Fax : 04.74.95.62.08 Internet : www.sferaco.fr E-mail : sferaco@sferaco.fr...
Page 8
DIMENSIONS DN 125 - 150 ( en mm ) : DN 125 - 150 Ref. Ø P Poids (en Kg) 38.86 50.72 Sferaco 90 rue du Ruisseau 38297 St Quentin Fallavier Tél : 04.74.94.15.90 Fax : 04.74.95.62.08 Internet : www.sferaco.fr E-mail : sferaco@sferaco.fr Date : 12/16...
Page 9
DIMENSIONS PLATINE ISO ET AXE ( en mm ) : DN 15 – 50 DN 65 – 100 DN 125 – 150 Ref. Ø K N x Ø Z 4x 6 4x 7 4x 9 4x 11 4x 11 4x 11 4x14 4x14 16.5...
Page 10
DIMENSIONS BRIDES ( en mm ) : Ref. Ø C Ø D Ø K Nb x Ø L 4 x 14 4 x 14 4 x 14 4 x 18 4 x 18 4 x 18 4 x 18 8 x 18 8 x 18 8 x 18 8 x 22...
Page 11
COUPLES DE MANŒUVRE ( en Nm sans coefficient de sécurité ) Couple ( Nm ) NORMALISATIONS Fabrication suivant la norme ISO 9001 : 2008 DIRECTIVE 97/23/CE : CE N° 0035 Catégorie de risque II module D1 Certificat 3.1 sur demande ...
Page 12
INSTRUCTIONS DE MONTAGE ET MAINTENANCE : REGLES GENERALES : Bien vérifier l’adéquation entre le robinet et les conditions de service réelles (nature du fluide, pression et température) Prévoir suffisamment de robinets pour pouvoir isoler les tronçons de tuyauterie pour faciliter l’entretien des matériels.