Sommaire des Matières pour Halsey Taylor HTVBLEE Serie
Page 1
HTV8BLEE*1D HTV8BLEE*2D HTVDBLEE*1D HTVDBLEE*2D OWNERS MANUAL MANUAL DEL PROPIETARIO HALSEY TAYLOR MANUEL DE L’UTILISATION HALSEY TAYLOR ™ HTVBLEE Series Barrier-Free Water Coolers ™ HTVBLEE La Barrera de la serie Liberta Agua Coolers ™ HTVBLEE Coolers d’Eau de Barrière-Libère de feuilleton 21, 61 See Fig.
Page 3
HTV8BLEE*1D HTV8BLEE*2D HTVDBLEE*1D HTVDBLEE*2D El PARENTESIS del GANCHO & LE CROCHET DE CINTRE & HANGER BRACKET & TRAP INSTALLATION la INSTALACION de la TRAMPA L’INSTALLATION DE PIEGE 1) Remove the hanger bracket fastened to back of the cooler by removing one (1) screw. 1) Quita gancho paréntesis abrochó...
Page 4
HTV8BLEE*1D HTV8BLEE*2D HTVDBLEE*1D HTVDBLEE*2D Top Cover Removal Please remove bottom cover before removing top cover. To remove top cover (Item 34), use a small Fig. 4 screwdriver to release the snap for the top cover as shown in Fig. 4. Then pull the small tabs on each side of the top cover outward slightly and slide upward to remove.
Page 5
HTV8BLEE*1D HTV8BLEE*2D HTVDBLEE*1D HTVDBLEE*2D Removing the basin To remove the basin (Item 32), remove two screws (Item 22) on top of the basin (Shown in Fig. 6). Then remove the four screws (Item 54) located underneath the dispenser bottom (Item 36). Finally pull polytube (Item 17) out of bubbler (Item 16) as shown in Fig.
Page 6
HTV8BLEE*1D HTV8BLEE*2D HTVDBLEE*1D HTVDBLEE*2D Fig. 9 Fig. 10 12, 18, 19 Bottom Cover Removal To access the refrigeration system and plumbing connections, remove two screws (Item 53) to remove bottom cover (Item 35). See Fig. 9. Tapa Inferior La eliminación Para accesar al sistema de refrigeración y las conexiones de empalmes, desmonte los dos tornillos (Articulo 53) para retirar la tapa inferior (Articulo 35).
Page 7
HTV8BLEE*1D HTV8BLEE*2D HTVDBLEE*1D HTVDBLEE*2D SENSOR RANGE ADJUSTMENT: (A) The electronic sensor used in this cooler is factory pre-set for a “visual” range of 36 inches (914 mm). If actual range varies greatly from this or a different setting is desired, follow the range adjustment procedure below: Using a small tip screwdriver, locate range adjustment screw through the small hole between the sensor lenses Turn this screw clockwise to increase range and counterclockwise to decrease range...
Page 8
HTV8BLEE*1D HTV8BLEE*2D HTVDBLEE*1D HTVDBLEE*2D 220V PARTS LIST/ 220V LISTA DE PIEZAS/ 220V LISTE DES PIÈCES ITEM NO. PART NO. DESCRIPTION DESCRIPCIÓN DESCRIPTION 31431C Fan Motor Motor del ventilador Moteur du Ventilateur 36066C Power Cord (HTV8BLEE) Cable eléctrico (HTV8BLEE) Cordon d’Alimentation (HTV8BLEE) 36248C Valve - Solenoid Válvula - Solenoide...
Page 9
HTV8BLEE*1D HTV8BLEE*2D HTVDBLEE*1D HTVDBLEE*2D PARTS LIST/ LISTA DE PIEZAS/ LISTE DES PIÈCES ITEM NO. PART NO. DESCRIPTION DESCRIPCIÓN DESCRIPTION 100322740560 Gasket - Bubbler (upper and lower) Joint statique - barboteur (supérieur et inférieur) Obturador - Borboteador (Superior e inferior) 100806740570 Grommet - Compressor Mtg.