Taymor 06-8834S Instructions D'installation

INSTALLATION INSTRUCTIONS
06-8834S
SINGLE HANDLE KITCHEN FAUCET
THIS FAUCET MEETS OR EXCEEDS THE FOLLOWING STANDARDS:
cUPC, ASME A112.18.1, NSF-61 AND LOW LEAD COMPLIANT
THANK YOU FOR PURCHASING THIS TAYMOR PRODUCT. ALL TAYMOR PRODUCTS ARE CAREFULLY
ENGINEERED AND FACTORY TESTED TO PROVIDE LONG TROUBLE-FREE USE UNDER NORMAL CONDITIONS.
HAVE BASIC TOOLS READY
1
RECOMMENDED TOOLS:
Teflon tape Screwdrivers
Adjustable Flashlight
wrench and
pipe wrench
WARNING: READ ALL the instructions completely before beginning.
READ ALL warnings, care and maintenance information.
Taymor recommends calling a professional if you are uncertain about installing this product!
This product should be installed in accordance with all local and provincial plumbing and building codes.
Need Help? Please call our toll-free Customer Support line at
(WEST) 1-800-267-4774 (EAST ) 1-800-387-7064 for additional assistance or service.
TURN OFF THE MAIN WATER SUPPLY
2
Locate water supply inlets and shut off water supply
valves. These are usually found under the sink.
FAUCET INSTALLATION
3
A) Remove old faucet. Clean sink surface in preparation for new faucet. Before installation,
remove the quick connector (1) from the counterclockwise direction. Unscrew the nut (2),
and remove the washers (3 & 4). If installing the faucet assembly without the escutcheon,
begin with step B. If installing the faucet with the escutcheon, begin with step 3.
B) OPTIONAL FLANGE INSTALLATION. Before installation, ensure that the flange (1) is placed
on the bottom of the new faucet assembly. Insert the faucet body through the hole in the
sink. Install the rubber washer (2), metal washer (3) onto the threaded mounting shank.
Thread nut (4) onto mounting shank. Do not overtighten.
C) OPTIONAL ESCUTCHEON INSTALLATION. Before installation, remove the flange (1). Apply a
bead of plumber's putty or silicone caulk around the faucet openings. Install the gasket over
the three holes in your sink.
D) OPTIONAL ESCUTCHEON INSTALLATION. Insert the faucet body through the hole in the
gasket. Install the rubber washer (1), metal washer (2) onto the threaded mounting shank.
Thread nut (3) onto mounting shank. Do not overtighten.
E) After inserting the hose through the hole in the sink surface, reattach the quick connector
(1) by screwing it onto the threaded end of the hose (2) in a clockwise motion. Hand tighten
only.
F) Align block (1) and tabs on quick connect. Push quick connect housing firmly upward and
snap onto receiving block. Pull down moderately to ensure connection has been made. If
it is necessary to remove quick connect, squeeze tabs on hose between index finger and
thumb, then pull down to disconnect. After connecting the hose, install the weights (2) at
the bottom of the hose to ensure ease of function.
Do not, use plumber' putty on cultured marble or other
composite sinks. Putty will discolor the sink.
A B
4
3
2
1
D E
1
2
3
All manuals and user guides at all-guides.com
WITH OPTIONAL ESCUTCHEON
Your installation may require new supply
lines. (Supply lines are not included.)
Torque wrench Safety goggles Plumber's putty
TURN OFF
C
1
2
1
3
4
F
1
2
2
ATTACH THE HOT AND COLD SUPPLY LINES
4
Make connections to water lines. Use 1/2" I.P.S. faucet connections (2) or use supplied coupling nuts
(3) with 3/8" O.D. ball-nose riser (1). Use two wrenches when tightening. Do not over tighten.
FLUSHING THE WATER LINES
5
Pull the hose assembly out of the spout and remove the spray head by unscrewing
it from the hose in a counterclockwise direction. Be sure to hold the end of the hose
down into the sink and turn the faucet on to the warm postion where it mixes hot and
cold water. Flush the water lines for one minute. This flushes away any debris that
could cause damage to internal parts. Check for leaks. Re-tighten any connections
if necessary, but do not overtighten. Reinstall the spray hose. Note: Do not lose the
gasked (1) in the hose.
Silicone caulk
ADJUSTING SPRAY SETTINGS
6
By rotating the spray head end to the point you hear a click, you can alternate
between stream or spray function as desired.
TURN OFF
EXPLODED DIAGRAM FOR REFERENCE
7
MAINTENANCE Your new faucet is designed for years of trouble-free performance. Keep
it looking new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners, steel
wool and harsh chemicals as these will dull the finish and void your warranty.
3 - SPOUT
2 - INVERTER
1 - SPRAY HEAD
32 - ESCUTCHEON
31 - BASE PLATE
1
WEST 1-800-267-4774 | EAST 1-800-387-7064 | taymor.com
1
2
3
1
4 - WEARABLE RING
5 - SPOUT NUT
6 - O-RING
7 - CLIP
8 - O-RING
9 - BODY
10 - CARTRIDGE
11 - BONNET
29 - FLANGE
30 - WASHER
12 - CAP
16 - SCREW
19 - HOSE
28 - SHANK
20 - HOSE
27 - WASHER
26 - WASHER
21 - BLOCK
25 - NUT
22 - O-RING
23 - COUPLING NUT
24 - WEIGHT
CUSTOMER SERVICE
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
13 - HANDLE
14 - BOLT
15 - HANDLE SEAT
17 - INDEX
18 - CONNECTOR