Charging The Built-In Battery; General Operation - AEG BSS 4830 Mode D'emploi

- USB port type A for music playback
- AUX input
- Micro-B USB charging port + indicator lamp for
recharging the battery
Scope of delivery
1x Bluetooth sound system
1x Charging cable (type A USB to micro B USB)
1x AC adapter (with type A USB port for connecting the
charger cable)
1x Instruction manual
First Use of the Device/Introduction
• Select a proper place for the device. A dry, level and slip
proof surface is suitable.
• Make sure the device is vented sufficiently!
• Remove the protective film from the device, if present.

Charging the built-in Battery

Before you can use this device, you must charge the built-in
rechargeable battery. Charge the battery as follows:
1. Flip the rubberized cover (10) open.
2. Connect the charger cable to the micro B USB port
underneath the rubberized cover (10) and to the power
adapter. Plug the power adapter into a properly installed
wall socket. The indicator lamp lights up red and the bat-
tery charges.
3. When the battery has been charged completely, the
indicator lamp below the USB charger socket lights up
orange.
4. Unplug the power adapter from the mains and discon-
nect the charger cable from the device.
5. Then close the rubberized cover again.
CAUTION:
Never leave the unit unattended when it is charging.
NOTE:
• The charging time varies according to battery use.
• If the device is out of use for a long period of time,
charge the battery at least once every 6 to 12 weeks.
The battery will also constantly discharge when
switched off.
• When the battery is almost empty, a warning signal
sounds at intervals.

General Operation

Turning the device on/ off (5)
• Turn on the device by keeping the button pressed. The
device starts in BT mode.
• In order to turn off the device, press and hold the but-
ton again.
Volume
Press and hold the / button (6) or the /
ton (8) in order to adjust the volume as desired.
Sound Settings
If necessary, change the EQ setting in your playback unit to
create the best sound.
Playing back music files
There are three ways of playing your own music files with the
unit: via cable connection, wireless via Bluetooth, or via USB
port.
By cable (Cable not included)
1. Flip the rubberized cover (10) open.
2. Connect the 3.5 mm stereo RCA cable to an external
audio source. If required, use a suitable adapter (not
included).
3. Insert the other end of the cable into the AUX-IN jack on
the unit.
4. Press the MODE button (9) repeatedly until the AUX
indicator lamp (2) lights up.
5. Start the playback of your audio source. Listen to the
sound playback via the speaker.
6. For the further procedure, please refer to the user manual
of the external audio source.
Keep the rubberized cover closed when not in use.
NOTE:
If possible, adjust the volume of the external unit to a com-
fortable level.
Cordless via Bluetooth
Bluetooth involves a technology for wireless radio connec-
tion of devices over a short distance. Devices with Bluetooth
standard are transmitting between 2.402 and 2.480 GHz in
the ISM band (Industrial, Scientific and Medical). Interference
can be caused for example by WLAN-networks, DAB radios,
cordless phones, or microwave ovens which work on the
same frequency band.
This device offers you the possibility to use a Bluetooth-
enabled device. The functional radius is limited to approx.
15 metres depending on the surroundings and the unit used.
If your playing device supports the A2DP profile (Advanced
Audio Distribution Profile) and has a music-player function,
then you can also wirelessly transfer music to the device. The
A2DP profile involves a multi-vendor Bluetooth profile. By
streaming, stereo-audio signals are wirelessly transferred be-
tween the playing device (source) and the receiving device.
To be able to remotely control the source, the playback de-
vice must support the AVRCP profile (Audio Video Remote
Control Profile).
English
31
but-