Dixon VR6500 Instructions D'installation Et Mode D'emploi page 2

IMPORTANT: This elbow is designed for use with vapor 4" top seal service
station adapters. To properly operate and maintain your BAYCO VR6500,
VR6200, or VR6000 series elbow the following instructions are provided.
Please read with care as improper handling or maintenance may cause a
hazardous condition.
CAUTION: Do not modify your BAYCO VR6500, VR6200, or VR6000 series
elbow for any reason. It can result in a hazardous condition due to
operating difficulties or operation malfunction. Disassembly or tampering
will void the product warranty.
Never smoke or allow an open flame near your dispenser when handling
volatile materials such as gasoline and fuels. An explosion could result.
Remember safety is everyone's business.
Installation: Attach the mating inlet using the four socket head cap screws and
lock washers supplied. Coat cap screws with anti-seize compound.
Lubricate Stem: This product has been assembled with anti-seize compound
and lubricated for easy maintenance and trouble-free service. However, we
recommend lubricating the stem through the grease nipple using lithium
based or quality automotive type grease prior to service. It is
recommended to apply lubricant to grease nipple, cam arm bearings,
and other moving parts every month. Monthly inspection and
lubrication become mandatory for items that are seldom used.
Condensation, rain and road salts can cause corrosion build-up and
binding when product not in use.
Check Operation: VR6500 / VR6200 elbow: Place elbow bottom end on
service station adapter (elbow is designed for use with vapor 4" top seal
adapter only). Move operating handle to the 11 o'clock open/unclamped
position. Release and hold the safety latch if equipped with one. Move the
handle clockwise to 2 o'clock position for full clamping (lever cannot be
moved any farther). Check locking arms on adapter. If the elbow is fitted
with a safety latch, make sure the stem pin is in the latch notch, preventing
movement of operating handle. Release by moving handle to 11 o'clock. If
fitted with safety latch, lift the latch lever and operating lever at the same
time.
VR6000 elbow with D-handle: Place elbow bottom end on service station
adapter. Pulling on D-handle is not necessary, coupler mechanism is self-
engaging; simply push elbow vertically down onto service station adapter
until locking arms pop in. Now push down on handle to ensure full
clamping (handle cannot be moved any farther). Check locking arms on
adapter. Release by pulling on handle until locking arms disengage.
All manuals and user guides at all-guides.com
Care & Handling: Bayco drop elbows are tested at the factory and are in
proper working condition when shipped. Drop elbows are designed to be
tough and to provide long service with reasonable care and handling. To
ensure long service Bayco elbows should not be thrown, dropped or
dragged; such actions may compromise the integrity and reduce the
service life of the product.
Inspect for Damage: Drop elbows can fail to operate if not properly
maintained. If the VR6500 / VR6200 / VR6000 elbow develops any
problems, remove from service and contact your Bayco distributor
describing the difficulty. The distributor will provide further instructions for
repair and warranty of the product.
Elbows should be inspected monthly. Check the adapter-to-elbow o-
ring seal and the flange where the base is attached to the elbow body for
any signs of leakage. Change seals if necessary. Check and tighten all
fasteners periodically. Lubricate the lever stem. Check the bushings and
replace if cracked or worn, and change if required. Check operation as
per above.
Regularly Replace Bushings: Some Bayco elbows contain polymer
Optional Accessories: The following are available as optional accessories
DIXON BAYCO WARRANTY: For complete warranty information, please
bushings, which protect and extend service life of bronze locking
arms. The bushings are designed to wear (instead of bronze arms)
and should be replaced every few months.
encouraged to inspect and replace polymer bushings to obtain
maximum elbow performance and longevity.
for VR6200 and VR6000 elbows;
Safety latch kit #6200SLK (VR6200 only),
Installation instructions are included with the items when ordered for
retrofit.
refer to the inside back cover of the latest Dixon catalogue.
Operators must be
090097 R6