Télécharger Imprimer la page

Publicité

Liens rapides

LPL600B/LPL600DBZ/LPL600G Owner's Manual
Location of Controls
1. 3 Super Bright LEDs
2. ON/OFF/DIMMER Switch
3. Flexible Neck with Pivoting Head
4. EZ Clip Mounting Bracket
5. Screw Mounting Bracket
Installation
EZ Clip Bracket (included)
The LED picture light is pre-assembled to the EZ clip bracket.
1. Attach EZ Clip Bracket to light by turning the EZ clip bracket clockwise until it is tight.
Hand tighten only.
2. To attach EZ Clip bracket to picture frame:
Open clips, place over picture frame and slowly release until the clips grasp the frame.
Check to make sure the clips are secure. For frames 1/2" to 1-1/4" thick.
3. Adjust neck and tilt head to desired position.
Screw Mount Bracket (included)
1. Remove EZ Clip bracket from fl exible neck by rotating the EZ Clip bracket
counter-clockwise until loose.
2. Place screw end of fl exible neck into screw mount bracket. Turn the screw mount bracket clockwise until it is tight. Hand tighten
only. Do not over tighten.
3. To attach screw mount bracket to picture frame: The screw mount bracket has
5 mounting holes. Select the hole pattern best suited to your frame or
mounting requirements.
4. Place screw mount bracket over top of the frame with the screw holes facing the back
of frame.
5. Insert up to three (3) screws (included) through the holes in the screw mount bracket into the frame to secure properly. Drill a pilot
hole for each screw to prevent the frame from cracking when inserting screws.
NOTE: Depending on the thickness of the frame, shorter screws may be required
(not included).
Do NOT put screws through picture. Check to make sure the screw mount is secure.
6. Adjust neck and tilt head to desired position.
Operating Directions
Light Positioning
Adjust the fl exible neck to the desired position. Pivot head to the desired angle.
ON/OFF/DIMMER Operation
• Press power symbol once for full brightness.
• Press again for softer light.
• Press a third time to turn the light off.
Inserting/Replacing the Batteries
If the LEDs appear to be dim this is an indication that your batteries need to be replaced.
1. Remove battery compartment cap at the end of the picture light by rotating 1/8 of a turn clockwise and pulling cap off.
2. Remove old batteries (if replacing batteries).
3. Replace with three new AAA batteries.
4. Make sure to follow battery polarity guide when installing new batteries.
5. Replace battery compartment cap and rotate 1/8 of a turn counter-clockwise to lock cap in place.
Battery Precautions:
1. Use only the size and type of batteries specifi ed.
2. Always purchase the correct size and grade of battery most suitable for the intended use.
3. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Reversed
batteries may cause damage to the device.
4. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel Cadmium) batteries.
5. Replace all batteries of a set at the same time. Do not mix old and new batteries.
6. Clean the battery contacts and also those of the device prior to battery installation.
7. Do not dispose of batteries in fi re.
8. Remove batteries if consumed or if product is to be left unused for an extended period of time.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Modifi cations to this product not approved by the party responsible for compliance could void the user's authority to operate the product.
Limited Warranty
Under normal use and conditions, AmerTac provides to the original purchaser of this product a one year limited
express warranty that is set forth in the Limited Warranty stated in full at www.amertac.com/warranties. The
Limited Warranty is in lieu of all other express or implied warranties or liabilities subject to the exceptions
explained fully in the Limited Warranty on the website.
WIRELESS LED
PICTURE LIGHT
1
3
4
250 Boulder Dr.
Breinigsville, PA 18031
610-336-1330
www.amertac.com
Made in China / Fabriqué en
Chine / Fabricado en China
© 2018 AmerTac™
I18-0068-A
2
5

Publicité

loading

Sommaire des Matières pour Ritelite LPL600B

  • Page 1 WIRELESS LED PICTURE LIGHT LPL600B/LPL600DBZ/LPL600G Owner’s Manual Location of Controls 1. 3 Super Bright LEDs 2. ON/OFF/DIMMER Switch 3. Flexible Neck with Pivoting Head 4. EZ Clip Mounting Bracket 5. Screw Mounting Bracket Installation EZ Clip Bracket (included) The LED picture light is pre-assembled to the EZ clip bracket.
  • Page 2 DEL sans fil l’image lumière Las luces LED de la foto inalámbrica Manuel du propriétaire LPL600B/LPL600DBZ/LPL600G LPL600B/LPL600DBZ/LPL600G Manual del propietario Emplacement des commandes Ubicación de los controles 1. 3 DEL très brillantes 1. 3 LED súper brillantes 2. Interrupteur ALLUMER/ÉTEINDRE/ATTÉNUER 2.

Ce manuel est également adapté pour:

Lpl600dbzLpl600g