Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Description
The 1504 and 1505 Series are flush wall mount door holders for use with
single doors. All are UL and cUL Listed and FM approved.
Installation
Install and wire in accordance with applicable codes, standards, such as
NFPA publications 70 (National Electrical Code), 72 (National Fire Alarm
Code), and 80 (Standard for Fire Doors and Fire Windows), and/or
other regulations applicable to the country and locality of installation and
in accordance with authorities having jurisdiction.
1.
Using Figure 1 and Table 2, locate the intersection of
X and Dimension Y. Dimension Z is shown at the intersection in the
gray area.
NOTE: If dimension X or Y is not shown on the chart,
extrapolate Dimension Z. (i.e., if X=7, and Y=30, Z =
(27-5/8 - ((27-5/8 - 27-1/4)/2) => Z = 27-9/16"
2.
Mount a single gang outlet box (not supplied) vertically on the
horizontal center line and 5" from the top of the door.
Y
Door
Door jamb
Figure 1. Locating the Door Holder
NOTE: The outlet box must be able to withstand a maximum
holding force of 50 pounds.
If X and Y intersect in the blank area in Table 2, DO NOT install
thbox. The contact plate and electromagnet cannot be aligned with
these dimensions.
28
30
2
26 (660)
28 (711)
4
26 (660)
28 (711)
6
25 5/8 (651)
27 5/8 (702)
8
25 1/4 (641)
27 1/4 (692)
10 24 5/8 (625)
26 3/4 (679)
12 23 3/4 (603)
25 7/8 (657)
14 23 3/4 (603)
25 (635)
16 21 3/4 (552)
24 (610)
18 20 (508)
22 1/2 (572)
20 18 1/4 (463)
21 (533)
22
18 3/4 (476)
24
26 Do not install outlet box if
28 Dimensions X and Y intersect in this blank area.
30 The armature and electromagnet cannot be aligned.
32
CHESHIRE, CT 203-699-3300 CUST. SERV. FAX 203-699-3365 TECH SERV. FAX 203-699-3078
Installation Instructions for Flush Wall Mount Electromagnetic
Dimension
center
line
Outlet box
Z
Wall line
X
Table 2. Dimension chart (in inches (mm))
32
34
29 7/8 (759)
32 (813)
34 (864)
29 7/8 (759)
32 (813)
34 (864)
29 5/8 (752)
31 3/4 (806)
33 3/4 (857)
29 1/4 (743)
31 3/8 (797)
33 1/2 (851)
28 3/4 (730)
30 7/8 (784)
33 (838)
28 (711)
30 1/8 (765)
32 1/4 (819)
27 1/4 (692)
29 3/8 (746)
31 1/2 (800)
26 1/4 (667)
28 1/2 (724)
30 3/4 (781)
25 (635)
27 3/8 (695)
29 3/4 (756)
23 1/2 (597)
26 (660)
28 1/2 (724)
21 5/8 (549)
24 3/8 (619)
27 (686)
22 1/2 (572)
25 1/2 (648)
Door Holders Catalog Series 1504 and 1505
Cat. No.
1504-E1
1504-E5
1504-AQN5
1505-E1
1505-E5
1505-AQN5
Electromagnet Assembly Mounting
NOTE: The combined projection of the 1504 series door holder is 3-7/
16" and the combined projection of the 1505 series door holder is 2-7/
16".
1.
Install the cover bracket in the outlet box with the field wiring below
the bracket (Figure 3).
To prevent electrical shock, ensure power is discon-
nected.
2.
Pull field wiring through conduit.
3.
Establish earth-ground continuity in accordance with applicable
codes, standards and authorities having jurisdiction.
4.
For -E1 and -E5 models, connect the field power wiring to the
electromagnet assembly wiring leads.
For -AQN5 models, refer to Figure 2 and connect as instructed
below:
120V AC operation. Connect power field wiring to terminals
a.
marked "120V AC" and "COM."
b.
24V AC/DC operation. Connect power field wiring to
terminals marked "24V AC/DC" and "COM."
5.
Secure the electromagnet assembly to the cover bracket with the two
#10-32 X 7/8" screws provided (Figure 3).
Y = Dimension of door width
36
38
40
36 (914)
38 (965)
36 (914)
38 (965)
35 3/4 (908)
37 3/4 (959)
35 1/2 (902)
37 3/8 (949)
35 (889)
37 (940)
34 3/8 (873)
36 3/8 (924)
33 3/4 (857)
35 7/8 (911)
33 (838)
35 1/8 (892)
32 (813)
34 1/4 (870)
30 7/8 (784)
33 1/8 (841)
29 3/8 (746)
31 3/4 (806)
28 1/8 (714)
30 5/8 (778)
26 1/4 (667)
29 (737)
Table 1. Specifications
Volts
12V DC
12V AC 60 Hz
24V AC 60 Hz
24V DC
120V AC 60 Hz
12V DC
12V AC 60 Hz
24V AC 60 Hz
24V DC
120V AC 60 Hz
WARNING
42
44
40 (1016)
42 (1067)
43 7/8 (1114) 45 5/8 (1159)
40 (1016)
42 (1067)
43 7/8 (1114) 45 5/8 (1159)
39 3/4 (1010) 41 3/4 (1060) 43 5/8 (1108) 45 3/8 (1153)
39 1/2 (1003) 41 1/2 (1054) 43 3/8 (1102) 45 1/4 (1149)
39 1/8 (994)
41 1/8 (1045) 43 (1092)
38 1/2 (978)
40 5/8 (1032) 42 1/2 (1080) 44 3/8 (1127)
38 (965)
40 (1016)
42 (1067)
37 1/4 (946)
39 3/8 (1000) 41 3/8 (1051) 43 3/8 (1102)
36 1/2 (927)
38 5/8 (981)
40 5/8 (1032) 42 1/2 (1080)
35 3/8 (899)
37 5/8 (956)
39 5/8 (1006) 41 5/8 (1057)
34 1/8 (867)
36 1/2 (927)
38 5/8 (981)
33 1/8 (841)
35 5/8 (905)
37 7/8 (962)
31 5/8 (803)
34 1/4 (870)
36 1/2 (927)
29 3/4 (756)
32 1/2 (826)
34 7/8 (886)
27 3/4 (705)
30 5/8 (778)
33 (838)
31 3/8 (797)
P/N 3100537 ISSUE 2 © 2004
Amps
0.170
0.150
0.015
0.015
0.015
0.170
0.150
0.015
0.015
0.015
46
48
44 7/8 (1140)
43 7/8 (1114)
40 3/4 (1035)
40 (1016)
38 5/8 (981)
37 1/8 (943)
35 3/8 (899)
33 7/8 (860)
501-152500-0-01
Publicité
Sommaire des Matières pour Edwards Signaling & Security Systems 1504 Serie
- Page 1 Installation Instructions for Flush Wall Mount Electromagnetic Door Holders Catalog Series 1504 and 1505 Table 1. Specifications Description Cat. No. Volts Amps The 1504 and 1505 Series are flush wall mount door holders for use with single doors. All are UL and cUL Listed and FM approved. 1504-E1 12V DC 0.170...
- Page 2 Door Plate 1 5/8" Armature (base view) (41 mm) VIEW Contact plate DOOR adjusting screw Mounting holes FRONT (2) #1/4-20 x 2" VIEW (51 mm) 120V AC 24V AC/ 1 3/4" screws provided (44 mm) for a standard 1 3/4" (44 mm) door 2"...
- Page 3 Instructions pour l’installation des dispositifs électromagnétiques de retenue de porte à montage mural encastré, séries 1504 et 1505 Description Tableau 1 Caractéristiques électriques Les appareils des séries 1504 et 1505 sont des dispositifs à montage mural de cat. Ampères Vo l ts encastrés, conçus pour retenir une seule porte.
- Page 4 1 5/8 po Armature Plaque de porte Vue de (41 mm) (vue de la base) dessus PORTE Mounting holes Vue de 2 vis n 1/4-20 x face 2 po (51 mm) 1 3/4 po 120V AC 24V AC/ fournie pour une (44 mm) porte standard de 1 3/4 po...