Additional Warnings - Nakayama PRO EB3600 Mode D'emploi

EN
PREPARATION
1. Obtain ear protection and safety glasses. Wear them at all times while operating the machine.
2. While operating the machine always wear substantial footwear and long trousers. Do not operate the machine when barefoot or wearing open sandals. Avoid
wearing clothing that is loose fitting or that has hanging cords or ties.
3. Do not wear loose clothing or jewelry that can be drawn into the air inlet. Keep long hair away from the air inlets.
4. Operate the machine in a recommended position and only on a firm, level surface.
5. Do not operate the machine on a paved or gravel surface where ejected material could cause injury.
6. Before using, always visually inspect to see, that the shredding means, bolts and other fasteners are secure, the housing is undamaged and that guards and
screens are in place. Replace worn or damaged components in sets to preserve balance. Replace damaged or unreadable labels.
7. Before use, check the supply and extension cord for signs of damage or aging. If the cord becomes damaged during use, disconnect the cord from the supply
immediately. DO NOT TOUCH THE CORD BEFORE DISCONNECTING THE SUPPLY. Do not use the machine if the cord is damaged or worn.
8. Never operate the machine while people, especially children, or pets are nearby.
9. Keep extension cords away from moving hazardous parts to avoid damages to the cords which can lead to contact with live parts.
OPERATION
1. Before starting the machine, make certain that the feeding chamber is empty.
2. Keep your face and body away from the feed intake opening.
3. Do not allow hands or any other part of the body or clothing inside the feed-
ing chamber, discharge chute, or near any moving part.
4. Keep proper balance and footing at all times. Do not overreach. Never stand
at a higher level than the base of the machine when feeding material into it.
5. Always stand clear of the discharge zone when operating this machine.
6. When feeding material into the machine be extremely careful that pieces of
metal, rocks, bottles, cans or other foreign objects are not included.
7. If the cutting mechanism strikes any foreign objects or if the machine should
start making any unusual noise or vibration, immediately shut off the power
source and allow the machine to stop. Disconnect the machine from the supply
and take the following steps before restarting and operating the machine:
i) inspect for damage;
ii) replace or repair any damaged parts;
iii) check for and tighten any loose parts.
8. Do not allow processed material to build up in the discharge zone; this may
prevent proper discharge and can result in kickback of material through the
intake opening.
9. If the machine becomes clogged, shutoff the power source and disconnect
the machine from supply before cleaning debris.
10. Never operate the machine with defective guards or shields, or without
safety devices, for example debris collector in place.
11. Keep the power source clean of debris and other accumulations to prevent
damage to the power source or possible fire.
12. Do not transport this machine while the power source is running.
13. Stop the machine, and remove plug from the socket. Disconnect the supply
and make sure that all moving parts have come to acomplete stop
- whenever you leave the machine,
- before clearing blockages or
unclogging chute,
- before checking, cleaning or working on
the machine.
14. Do not tilt the machine while the power source is running.
RECOMMENDATIONS WHEN USING THE PRODUCT
1. Operate the machine only at reasonable hours – not early in the morning or
late at night when people might be disturbed.
2. Use rakes and brooms to loosen debris before blowing/vacuuming.
3. Slightly dampen surfaces in dust conditions or use mister attachment.
4. Use the full blower nozzle extension.
5. Supply the product via a residual current device (RCD) with a tripping current
of not more than 30mA.
6. Avoid using the machine in bad weather conditions especially when
there is a risk of lightning.
MAINTENANCE AND STORAGE
1. When the machine is stopped for servicing, inspection, or storage, or to
change an accessory, shut off the power source, disconnect the machine from
the supply and make sure that all moving parts are come to a complete stop.
Allow the machine to cool before making any inspections, adjustments, etc.
Maintain the machine with care and keep it clean.
2. Store the machine in a dry place out of the reach of children.
3. Always allow the machine to cool before storing.
4. When servicing the shredding means be aware that, even though the power
source is switched off due to the interlock feature of the guard, the shredding
11
means be aware that, even though the power source is switched off due to the
interlock feature of the guard, the shredding means can still be moved.
5. Replace worn or damaged parts for safety. Use only genuine replacement-
parts and accessories.
6. Never attempt to override the interlocked feature of the guard.

ADDITIONAL WARNINGS

1. Warning! Do not operate the product near open windows, etc.
2. Do not blow hard objects such as nails, bolts, or rocks.
3. Apply extra care when cleaning debris from stairs or other tight areas.
4. Keep all parts of your body away from the suction/blowing device. Do not
remove blockages or jams when the product is switched on. Make sure the
switch is off when clearing jammed material. One moment of inattentiveness
while operating the product may result in serious personal injury.
5. Carry the product by the handle with the motor off. Handling the product
properly reduces the possibility of personal injury.
6. Never use the product standing on steps or a ladder. Do not work above
shoulder height.
7. If the product starts to vibrate abnormally, check it immediately. Excessive
vibration can cause injury.
8. Always ensure the product is fully assembled before using it. Never attempt
to use an incomplete product or one fitted with an unauthorized modification.
9. Check the suction/blowing device regularly for damage, and if damaged re-
pair immediately.
10. Do not overload the product.
11. Follow the maintenance and repair instructions for this product. Never carry
out any modifications to the product. Information about maintenance and re-
pair is provided in this user manual.
12. If the power cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified people in order to avoid a hazard.
13. Switch-off the machine before attaching
or removing the bag.
EMERGENCY
Familiarize yourself with the use of this product by means of this instruction
manual. Memorize the safety directions and follow them to the letter. This will
help to prevent risks and hazards. (1) Always be alert when using this product,
so that you can recognize and handle risks early. Fast intervention can prevent
serious injury and damage to property. (2) Switch off and disconnect from the
power supply if there is any malfunction. Have the product checked by a quali-
fied specialist and repaired, if necessary, before you put it into operation again.
RESIDUAL RISKS
Even if you are operating this product in accordance with all the safety
requirements, potential risks of injury and damage remain. The following
dangers can arise in connection with the structure and design of this product:
1. Health defects resulting from vibration emission if the product is being used
over long periods of time or not adequately managed and properly
maintained.
2. Injuries and damage to property due to broken accessories or the sudden
impact of hidden objects during use.
3. Danger of injury and property damage caused by flying objects.
WARNING
This field might interfere with active or passive medical implants! Consult your
doctor and the medical implant manufacturer before operating the electric
blower, το reduce the risk of serious or fatal injury. In the event of accident or
breakdown, release the trigger to stop the machine, and disconnect the power
supply.
WWW.NIKOLAOUTOOLS.GR
This product produces an electromagnetic field during operation!