HUDSON VALLEY LIGHTING 1541 Guide D'installation

MOUNTING PLATE
WALL ANCHOR
BACK PLATE
SIDE GLASS
FRONT GLASS
CLIP
SMALL SCREW
Thank you for purchasing our lighting fixture.
Please clean with a soft, dry cloth ONLY! Do
not use cleansers.
www.hudsonvalleylighting.com
GENERAL
1. To ensure the success of the fixture installation, the following instructions and diagram(s)
should be read and understood.
2. All electrical connections must be made in accordance with the National Electric code and
local codes and ordinances. If you are uncertain of the methods of installing electrical wiring
and lighting fixtures secure the services of a qualified licensed electrician.
TOOLS NEEDED
Blade screwdriver, Phillips screwdriver, slip joint pliers or small adjustable wrench, wire
SAFETY CABLE
cutter/stripper, electrical current tester, stepladder and electrical tape.
CABLE CLAMP
INSTALLATION PREPARATION
MOUNTING SCREW
1. TURN OFF THE ENTIRE ELECTRICAL CIRCUIT TO WHICH THE
GROUND SCREW
LIGHTING FIXTURE IS TO BE ATTACHED. Turn circuit breaker to the "off" position
WALL ANCHOR
or completely remove the fuse controlling the circuit.
WOOD SCREW
2. If an existing fixture is being replaced, remove it and note to which of the wires in the
outlet box the fixture was attached. DO NOT SEPARATE MULTIPLE TWISTED
LAMP
WIRES THAT MAY BE IN THE BOX. DO NOT DAMAGE THE INSULATION
OF OLDER WIRING. In regular circumstances the BLACK wire will be the "Hot" lead and
the WHITE wire will be the "Neutral" or "Common" lead. A GREEN or BARE COPPER wire
is the "Ground". In older buildings it is always good practice to reconfirm the polarity of the
wiring.
FIXTURE INSTALLATION
1.Remove the fixture and parts bag(s) from the carton. Before discarding the carton, double
check packing to make certain that all parts are found.
2. Using the mounting plate mark holes on the wall for the anchors. Drill holes on the wall and
push the anchors into the wall. Place the mounting plate back over the wall and secure with the
screws into each anchor, and outlet box.
3. Feed the SAFETY CABLE through one of the holes on the mounting plate, loop the SAFETY
CABLE over the mounting plate.
4. Feed the SAFETY CABLE through the cable clamp. Tightly the cable clamp to lock the SAFETY
CABLE in position.
5. Gently place the flat glasses into the frame as shown in the figure, and then secure them with
clips and small screws
6. Fasten the bare ground wire to the green or bare copper wire in the outlet box or the green
screw on the mounting plate.
NEVER FASTEN THE GROUND WIRE TO THE BLACK OR "HOT" WIRE !
FAILURE TO FOLLOW THIS INSTRUCTION COULD RESULT IN SERIOUS
INJURY OR DEATH !
7. Fasten the black fixture wire to the white wire in the outlet box.
Fasten the wires together with an approved fastener (wire nut) Starting about 1" below the
fastener, tightly wrap the connection with electrical tape so that the tape seals the end of the
fastener. Make sure that there is no exposed wire or strands that could cause a
dangerous short circuit!
8. Connect the black fixture wires to the black wire in the outlet box. Fasten the
joined wires as in step 7.
9. Place the back plate over the outlet box and fasten it by set screws.
10. With silicone caulking compound, caulk completely around where the back plate meets with
the wall surface.
CAUTION: Be sure to caulk completely where the back plate meets the wall surface
to prevent water from seeping into the outlet box.
11. Install the lamp(s). The fixture is rated for 75-watt type T lamps.
DO NOT EXCEED RECOMMENDED WATTAGE !
12. Restore power to circuit at breaker or fuse box.
DIMMING
The fixture can be controlled by a wall dimming device. Only use Triac/electronic dimmer. Make
sure the carton is marked for use with LED compact fluorescent-incandescent light source only.
These can be provided by your local electrical distributor, home center, or hardware store.
1541