Rocelco MVL Medium Instructions D'installation

Publicité

Les langues disponibles

Les langues disponibles

Rocelco MVL Medium Very Low Profile Mount Installation Instructions
Designed for LED/LCD/Plasma flat panels (26"-42") up to 36.4kg (80lbs).
Warning!
This product should only be installed by someone who is experienced with tools, is familiar with basic
wall construction, and fully understands these instructions. Ensure that the supporting wall will safely support the
combined load of the TV screen, and all attached hardware and components. If you cannot identify the type of wall or
you are not certain that the wall is strong enough to support the weight of the mount and TV, you must use a
professional installer, who may need to reinforce the wall. Tighten screws firmly but do not over-tighten, which can
damage the fasteners, greatly reducing their strength. Check carefully to ensure that there are no missing or
defective parts. Do not use any components that appear to be damaged or defective, this may result in damage or
serious injury. Improper installation may lead to damage or serious injury. Do not use this product for any purpose for
which it was not designed. Hollow walls, gypsum board and similar materials will not support the weight of a TV, you
must mount into very strong and solid material behind the wall, such as 2"x4" wood studs or brick/concrete. The wall
mounting hardware supplied with this product is designed for wood stud or concrete/brick walls only. If you are
mounting on a steel stud wall or old cinder block wall, you will need to source alternative wall mounting hardware.
The manufacturer, distributor or dealers are not responsible or liable for any damages, injuries or losses caused by
improper use, assembly, installation or failure to follow the installation instructions or safety warnings. Due to the
small components used in the construction of this unit, small children must be kept away during assembly. If you
have any doubts about the safety of the wall or the installation, your ability to perform the installation properly, or any
of the above warnings, you must use a professional installer.
Tools required:
5mm drill bit, 10mm masonry drill bit used for concrete installation, 11/20"(14mm) ratchet wrench ,
and a Phillips screwdriver. Identify & ensure that you have all components & hardware as per figure 1 below:
2-Left &Right TV interface arm-(BB)
1-Wall Bracket-(AA)
3- Locking bar -(CC)
4-M5*15 Screws(A)
4-M5*35 Screws(B)
4-M6*15 Screws(C)
4-M6*35 Screws(D)
4-M8*15 Screws(E)
4-M8*35 Screws(F)
4-square pad-(G)
4-spacer-(H)
1

Publicité

Table des Matières
loading

Sommaire des Matières pour Rocelco MVL Medium

  • Page 1 Rocelco MVL Medium Very Low Profile Mount Installation Instructions Designed for LED/LCD/Plasma flat panels (26"-42") up to 36.4kg (80lbs). Warning! This product should only be installed by someone who is experienced with tools, is familiar with basic wall construction, and fully understands these instructions. Ensure that the supporting wall will safely support the combined load of the TV screen, and all attached hardware and components.
  • Page 2 4-metal washers (I) 4-lag bolts (J) 4-wall anchors-(K) 5MM*200 Allen Key figure 1 WALL BRACKET INSTALLATION WALL BRACKET INSTALLATION Into wood studs: Into wood studs: The wall bracket (AA) must be installed into two wood studs with a separation of at least 406 mm (15.98”). Use a stud The wall bracket (AA) must be installed into two wood studs with a separation of at least 406 mm (15.98”).
  • Page 3 Installing the TV interface arms to the back of your flat panel TV Caution: Never lay the flat panel, face down on the screen, it should be tilted leaning against the wall or other solid surface, laying the flat panel face down on the screen may lead to permanent damage. Before installation, the TV interface arms(BB) must be vertically placed and the distance from the flat panel should be as short as possible .Thread the screws (A,B,C,D) through the square pad (G), the TV interface arms (BB) and spacer ( H) if required, into the flat panel.
  • Page 4 Directives d’installation pour la monture moyenne à profil très bas Rocelco MVL Conçu pour les écrans DEL /LCD/Plasma (26"- 42") jusqu’à 36.4kg (80 livres) Attention! Ce produit doit seulement être installé par une personne qui a de l’expérience avec les outils, qui connaît bien la construction de base des murs, et qui comprend bien ces directives.
  • Page 5: Installation Du Support Mural

    4-vis M8*15 (E) 4-vis M8*35 (F) 4-coussinets carré (G) 4-espaceurs (H) 4- rondelles de métal (I) 4- boulons de retardement (J) 4-ancres à mur (K) Clé Allen 5MM*200 figure 1 INSTALLATION DU SUPPORT MURAL Dans des montants de bois : Le support mural (AA) doit être installé...
  • Page 6: Installer Les Bras D'interface À L'arrière De Votre Téléviseur À Écran Plat

    Attention Ne jamais percer dans un join de maçonnerie. Le béton doit être d'une densité minimale de 2000PSI béton concrete Attention Les ancres doivent être assis fermement sur le béton ou surla maçonnerie. Si vous montez le support su un mur de maçonnerie couvert de plaques de platre, alésez un trou dans les plaques de platre autour des trous de montage, afin de pouvoir appuyer les ancres directement contre le béton ou la...
  • Page 7: Accrochez Les Bras D'interface Du Téléviseur Au Support Mural

    Accrochez les bras d'interface du téléviseur au support mural Attention : Certains écrans plats sont lourds : deux personnes fortes sont nécessaires à l'installation. Levez et positionnez l'écran avec précaution. Levez le téléviseur avec les bras d'interface sur la barre de croisement du support mural (AA), et ensuite abaissez le en place jusqu'à...

Table des Matières