Publicité
Liens rapides
Dee Zee Running Board Installation Instructions
Congratulations on your purchase of a quality Dee Zee product. Dee Zee is
recognized as having the highest quality running boards and accessories on
the market today. We have earned this reputation by offering our customers
a product they can be proud to place on their vehicles. Dee Zee meets all
the criteria of manufacturing a custom-fit product which guarantees it to
be the easiest product to install.
Note: Please take time to read all of the instructions before beginning this installation.
Warning! Please check for wiring or other obstructions before drilling any holes into
the vehicle. If it is necessary to drill any holes into the vehicle, Dee Zee recommends
putting a sealant or rust inhibitor around all holes drilled into the body of the vehicle.
Warning! It is the sole responsibility of the vehicle owner to check for tire clearance.
Warning! It is unlawful and dangerous to ride on running boards or side box boards
while the vehicle is in motion.
Cleaning Instructions: To maintain the bright finish of your Dee Zee running boards,
clean with a mild detergent. For our stainless steel products and accessories, the
application of a high grade automotive type wax is recommended.
If you should happen to have any questions with this product or you have an
installation question, please feel free to call us at:
1-800-779-8222
If you would like to find out more information on Dee Zee's products please
feel free to visit our website at:
WWW.DEEZEE.COM
DZ 2038.PDF
10/18/02
Publicité
Manuels Connexes pour Dee Zee DZ 2038
Sommaire des Matières pour Dee Zee DZ 2038
- Page 1 Warning! Please check for wiring or other obstructions before drilling any holes into the vehicle. If it is necessary to drill any holes into the vehicle, Dee Zee recommends putting a sealant or rust inhibitor around all holes drilled into the body of the vehicle.
-
Page 2: Tools Required
Dee Zee Britetread Running Board Installation Instruction DZ 2038 (1999 - Current) Ford Superduty Crew Cab Pickup 1/4 x 3/4” 1/4“ Flat Britetread Rocker Running Britetread Washer Hex Head Mudflap Panel Board Running Bracket Bolt Bracket Board 1/4“ Hex Nut 1/4 x 1”... - Page 3 Secure britetread mudflap (B) to britetread running board (A) using 1/4 x 3/4” hex head bolts (E), 1/4” flat washers (F), and 1/4” hex nuts (G). Tighten into place using a 7/16” wrench / or socket. Place bulb-seal gasket (Q) onto the backlip of britetread running board (A) and trim flush with the britetread mudflap (B) and the end of britetread running board (A).
- Page 4 Locate the existingholes inthevehiclerockerpanelas shownbelow. Placean8mmu-clip (P)onto the holes s hown below andpress firmly into place. Trouvezlestrous existants danslepanneaudeculbuteurdevéhiculecommemontréci-dessous.Placez unu-clip d e 8 m m (P) dans les trous montrés ci-dessous etappuyezfermement dans l'endroit. Approximate Hole Locations on Vehicle 721/4” 513/8”...
- Page 5 Using the drawingbelowasaguideidentifytherockerpanelbracketandits correct position on the vehicle. Note: The open face o f r ocker panel bracket (C) will facetherearofthevehicleonthedriversideofthevehicle. Note: The open face o f r ocker panel bracket (C) will facethefrontofthevehicle onthepassengersideof thevehicle. Alignthe top hole as shown belowwiththe8mmu-clip(P)andsecure into place using an 8mm x 30mm hex head bolt(N) and 5/16"...
- Page 6 Usingthedrawingbelowas a guide, placerunningboardbracket (D) uptorockerpanelbracket(C). Secure the rear-top hole inrunningboardbracket (D) tothehole in the rockerpanel bracket (C)using 3/8 x 1" hex headbolt (I),5/16"flat washers (J), 3/8" lockwasher (L),and3/8"hexnut(K). Note: See drawings below for correct hole identification. Enutilisant le schéma ci-dessous commeguide, placezlaparenthèsecourante depanneau (d) jusqu'à la parenthèse d e panneau deculbuteur(c).Fixez le trou d'arrière-dessusdans laparenthèsecourantedepanneau(d) autroudansla parenthèsedepanneau deculbuteur (c) à...
- Page 7 Rotate therunning board bracket to the upright positionandsecureitinto placeusing a 3/8x1"hexheadbolt(I),3/8" lockwasher(L), 5/16" flatwashers(J),and 3/8" hex nuts(K)as shownbelow. Tournez le panneau courant jusqu à lapositiondroite et fixez-le dans l'endroit à l'aide d'unboulondetêted'hexade 3/8 x de1"(i),dela rondelledefreinage de 3/8" (l),desrondelles plates de5/16"(j), et des écrous d'hexade3/8"(k)comme montré...
- Page 8 Placebritetreadrunningboard(A)uptotherunningboardbrackets (D) asshownbelow. Slide the britetread running board u p to the rocker panel so thatitisflushwiththevehicle rocker panel. Placez le panneaucourant debritetread (a) jusqu'auxparenthèsesde panneau de fonctionnement (d)commemontré ci-dessous. Glissez lepanneaucourantdebritetread jusqu'au panneau de culbuteur desortequ'ilsoit affleurant du panneau deculbuteurdevéhicule. Rocker Panel Bracket Running Board...
- Page 9 Usingthebottomholes intherunning board bracket (D)as a guide,drill 1/4” holes through thebritetread running board. Secure the running board bracket(D)to the britetread running boardusing 1/4 x 1” ribneckcarriageheadbolts (H),1/4”flatwashers(F),and 1/4” hex nuts(G). Tighten into p l a c e u s i n g a Drill with a 7/16”...
- Page 10 Drill two holes through the britetread mudflap and the sheet metal of the vehicle wheel well opening. Secure the britetread mudflap to the vehicle wheel well opening using 1/4 x 1” sheet metal screws (M). Tighten into place using a 3/8” Drill with a wrench / or socket.