Product Parts - Martinelli Pliko Mini Instructions

EN_English
Thank you for choosing a Martinelli product.
WARNING
_ IMPORTANT: read the instructions carefully before
use and keep them for future reference. The child
may be hurt if you do not follow these instructions.
_ This item was designed for the transport of 1 child in
the seat.
_ Do not use this item for a number of occupants greater
than that intended by the manufacturer.
_ This item is approved for children from birth up to a
weight of 15 kg in the seat.
_ It may be dangerous to leave your child unattended.
_ Always use the 5-point harness and attach the waist
strap to the leg divider strap.
_ Be careful not to hurt the child when adjusting the
mechanisms (handlebar, backrest).
_ Always apply the brake when stopped and when
positioning the child in the seat or when removing the
child from the seat.
_ Assembly and preparation of the product, plus
cleaning and maintenance operations, must be carried
out exclusively by adults.
_ Do not use this item if there are parts missing or signs
of breakage.
_ Before use check that all the attachment mechanisms
are correctly insert.
_ Do not insert fingers into the mechanisms.
_ WARNING: Do not add a mattress.
_ Any load hanging on the handlebar or the handles
can make the stroller/carriage unstable; follow the
manufacturer's instructions for max load capacity.
_ Do not place loads over 5 kilos in the basket. Do not
place in the bottle holder weights heavier than stated
or hot drinks. Do not place in the hood pockets (if
applicable) weights over 0.2 Kg.
_ Do not use the item near to stairs or steps, heat
sources, naked flames or dangerous objects within
reach of the child.
_ The use of accessories not approved by the
manufacturer could be dangerous.
_ This item is not suitable for jogging or roller skating.
_ Do not use the rain canopy (if present) indoors and
regularly check to ensure the child is not too warm;
do not park the stroller close to heat sources and keep
well away from lighted cigarettes. Ensure the rain
canopy is not interfering with any moving parts of the
carriage or stroller; always remove the rain canopy
before folding your carriage or stroller.

PRODUCT PARTS

Check the package contents and contact our Customer
Service for any claim.
_ The PLIKO MINI stroller is composed of:
2 swivel or locking front wheel sets, 2 rear wheel sets,
basket, cup holder, hood, cover, rain canopy, double-
face padding.
INSTRUCTIONS
1• OPENING: to open the stroller, unhook the left hand
side lever (fig_a), hold the handles and at the same
time lift the stroller.
Check that the stroller has opened properly by
ensuring that the side hooks are well secured (fig_b).
2• If the hooks are not secured properly, press the seat
downwards (fig_d) until they click into place. Finally,
press downwards on PUSH with your foot (fig_e).
3• ASSEMBLING: to mount the front wheels, firstly check
that the washer is present, as shown in the figure, then
lower lever A and slip wheel B on until it clicks into
place.
4• To mount the rear wheels connected by the brake
cable, place them with the brake facing externally
(fig_a).
WARNING: ensure the hooks have clicked into place, as
in figure b.
5• Finally, hook the central element of the brake cable
onto the chassis, ensuring it clicks into place, as in the
figure.
6• BASKET: to mount the basket, slip the loops over the
rear hooks 1 and 2 and the front hook 3 (fig_a).
CUP HOLDER: It can only be fitted to the right hand
side of the stroller, using the clip which is already
present on the chassis. To fit the cup holder, push until
it clicks into place (fig_b).
ADJUSTING THE HANDLES: the height of the handles
can be adjusted. Press the little button behind the
handles and pull upwards. To lower the handles, do the
opposite (Fig. c).
7• SWIVEL WHEELS: In order to make the wheels swivel,
the lever (arrow 1) must be lowered. To secure the
wheels, move the lever to the opposite direction
(arrow 2). The rear wheels are fixed.
BRAKE: To set the brake on the stroller, lower the lever
on the rear wheel unit with your foot. To release the
brake, lift the lever (fig_b). When stationary, always
apply the brake.
8• HOOD: To fit the hood, click the fasteners onto the
appropriate points and button down the hood on the
rear of the stroller's backrest (fig_a).
The hood can be set to 2 positions (fig_b), simply by
pulling it backwards or forwards.
9• The section of the hood with netting can be drawn
out to keep the child out of the sunlight (fig_A) and
easily slipped back into the hood when it is no longer
necessary. The hood (fig_B) has a window to observe
the child (arrow 1), a large, useful pouch (arrow 2) and a
small strap to attach the child's favourite toy (arrow 3).
1 0• COVER: to put it on:- slip it on and button it up on the
sides of the chassis (fig_A);
- attach it to lower part of the chassis proceeding in this
way:- release the chassis by pulling both levers upwards
at the same time (fig_B), push the chassis down to
release it (fig_C);- slip the elastic round the front part of
the chassis, as shown in the picture (fig_D);
- fasten the elastic and attach the chassis, using the side
hooks (fig_E).
To check the chassis is attached correctly, please read
Point 2.
11• RAIN CANOPY: to put the rain canopy on, slip it onto
the stroller (fig_A), button it up on the sides of the
hood (fig_1) and fasten the elastics after pulling them
round the lower part of the stroller (fig_2).
DOUBLE-FACE PADDING: the stroller comes with a
double-face padding (fabric on one side, matelasse on
the other) (fig_B) which can be removed (follow the
instructions in point 19, figure 1 and 2).
- 13 -