Overview Of Parts - VOLTCRAFT 2127443 Mode D'emploi

b) Additional information on lithium rechargeable batteries
• Li-Ion batteries installed in this device require special care during charging/discharging, ope-
ration and handling.
• Never destroy or damage the rechargeable battery, do not drop it or puncture it with any
objects. Protect the rechargeable battery from mechanical stress. This may cause a fire or
explosion!
• Ensure that the device does not overheat during use, charging, discharging, transport and
storage. Do not place the device near heat sources and protect it from exposure to direct
sunlight. If the device overheats, there is a risk of fire and explosion!
• The device must not exceed a temperature of +60 °C.
• If a device is damaged or the outer cover is puffed/swollen, discontinue use of the device. Do
not recharge it. This may cause a fire or explosion!

Overview of parts

11
12
10
8
9
1 Button for charge level indicator and activation of LED light and power bank function
2 Charge level indicator
3 Protective cover
4 LED light
5 Micro USB charging input "Input"
6 USB charging output "Output"
7 Mechanically coded connection for starter cable
8 Relay housing
9 Pole terminals (red +, black -)
10 Force start button
11 Mechanically coded plug for quick start system
12 LED status indicator for starter operation
5 6
4
3
2
1
Start-up and charging
• The quick start system must be fully charged before use.
• Standard USB quick chargers with a charging current of at least 1 A are suitable for char-
ging. An output charging current of at least 1.5 A is recommended because it shortens the
charging time.
1. Connect the included charging adapter cable to the USB charger (not included).
2. Plug the Micro USB cable into the Micro USB charging input "Input" (5).
3. As soon as your USB charger provides sufficient charging current, the charging process
is indicated by the LEDs of the charge level indicator (2), which light up one after another.
4. If all 4 LEDs of the charge level indicator light up at the same time or are permanently lit, the
charging process is completed.
5. Remove the charging cable from the start system.
6. Briefly press the activation button (1) to display the current charge status.
View Meaning
7
4 LEDs Start system is fully charged and can be used without restriction.
3 LEDs Start system is 75% charged and can be used without restriction.
2 LEDs Start system is 50% charged. It can only be used as power bank or LED light.
1 LED Start system is 25% charged. It can only be used as power bank or LED light.
0 LED Start system is not ready for use and must be charged.
Operation
a) Start support function
The quick start system can support a weak starter battery when starting the engine. During
start-up a very high current is needed. The quick start system emits multiple high current pulses
during the start-up phase. This is usually enough to support a weak starter battery. If this is not
enough, press a force start button to enable a manual force start mode with a longer-lasting
current pulse for a maximum of 30 seconds.
Never short-circuit the two pole terminals. This will discharge the quick start system
and damage the rechargeable battery.
To perform a normal start-up operation, proceed as follows:
1. Check the charge status of the quick start system. For a start-up support at least 3 LEDs
must light up. If fewer LEDs are lit, the quick start system must first be charged.
2. Open the protective cover (3) on the quick start system.
3. Insert the plug (11) of the relay housing (8) into the connection for the starter cable (7). The
plug is mechanically coded and fits together only with the correct polarity. Ensure firm and
reliable contact.
4. The LED status indicator (12) on the relay housing (8) starts to flash green and red alter-
nately.
5. Connect the red pole terminal to the plus pole (+) and the black pole terminal to the minus
pole (-) of the car battery. Ensure that the contact is connected properly. Turn the terminals
back and forth to break possible oxide layers on the poles.
6. Once the contact is established, you will hear a normal clicking sound from the relay
housing. Start your car within 30 seconds. The quick start system now emits multiple current
pulses during the start-up phase. They should be enough to start the engine.
7. When the engine starts, disconnect the quick start system and remove the starter cable
from the quick start system. Close the connections with the protective cover.
8. If the engine does not start, disconnect the quick start system. Wait approx. 5 minutes and
then perform a manual force start operation.
To perform a manual force start operation, proceed as follows:
1. Check the charge status of the quick start system. For a start-up support at least 3 LEDs
must light up. If fewer LEDs are lit, the quick start system must first be charged.
2. Open the protective cover (3) on the quick start system.
3. Insert the plug (11) of the relay housing (8) into the connection for the starter cable (7). The
plug is mechanically coded and fits together only with the correct polarity. Ensure firm and
reliable contact.
4. The LED status indicator (12) on the relay housing (8) starts to flash green and red alter-
nately.
5. Connect the red pole terminal to the plus pole (+) and the black pole terminal to the minus
pole (-) of the car battery. Ensure that the contact is connected properly. Turn the terminals
back and forth to break possible oxide layers on the poles.
6. Once the contact is established, you will hear a normal clicking sound from the relay housing.
7. Press and hold down the force start button (10) on the relay housing (8) for approx. 3
seconds. The LED status indicator (12) turns green.
8. Start your car within 30 seconds. The quick start system now emits long current pulses
during the start-up phase. They should be enough to start the engine.
9. When the engine starts, disconnect the quick start system and remove the starter cable
from the quick start system. Close the connections with the protective cover.
10. If the engine does not start, disconnect the quick start system. Wait approx. 5 minutes asnd
then repeat a manual force start operation.
11. If the engine still does not start after three attempts, the start support process must be
terminated. Probably, the car battery is defective, or there is another problem. In this case,
have the vehicle checked by a specialist workshop.