Publicité
Liens rapides
POWER : 12VDC. We recommend power supply CEBEK FE-123 or FE-300, which is perfectly suited to the needs of the circuit.
compatible transmitters: TL-300, TL-301, TL-420, TL-421, TL-428, TL-429, TL-432 . Supports extensions: TL-424 / TL-425.
Install a switch that are necessary for the protection and safety, as reflected in the CE standard.
A positive and negative supply to the corresponding input terminal.
ACTIVATION RESET : This occurs when you close the "RESET" terminal with the common negative terminal indicated by the
ground symbol COM. When "RESET 1 /2/3/4/5/6/7/8 ", the corresponding relay will automatically switch to standby status,
regardless of the current order he was doing. The cable length should be as short as possible, if it is greater than 20 cm. you must
use shielded cable, connecting the shield to the corresponding terminal with the ground symbol.
ANTENNA : Must be installed before operating the remote control, we recommend the antenna Cebek C-0509 and C-0510 or 130
mm cable
ALIMENTATION : 12VDC. Nous recommandons l'alimentation CEBEK FE-123 - FE-300, ce qui est parfaitement adapté aux
besoins du circuit.
émetteurs compatibles: TL-300, TL-301, TL-420, TL-421, TL-428, TL-429, TL-432 . Prise en charge des extensions: TL-424 /
TL-425.
Installez un interrupteur qui sont nécessaires pour la protection et la sécurité, comme en témoigne la norme CE.
Une alimentation positive et négative à la borne d'entrée correspondante.
Power : 12 V .DC.
Maximum consumption : 450 mA.
Maxim output load : 7A (2A for indutive loads)
Reset input : Closure of contacts.
Antenna : 170 mm.
Working frequency : 433,92 Mhz.
LED indicators : Programming, Relays, Power
Relay Operation : Set Up in Monostable, bistable or Timed, (0,1 a 132 sec.)
Response time (Delay issuer order, relay response) : 0,5 seg
Compatibility : Issuers R.F. Group 3.
Weight :172 gr.
Size : 154 x 107 x 17 mm.
DIN rail : C-7592
www.cebek.com
-
Receiver R.F
Récepteur R.F
Receptor R.F
Receptor R.F
8 Channels, group 3
TL-423
TECHNICAL CHARACTERISTICS
sat@fadisel.com
Publicité
Manuels Connexes pour CEBEK TL-423
Sommaire des Matières pour CEBEK TL-423
- Page 1 DIN rail : C-7592 POWER : 12VDC. We recommend power supply CEBEK FE-123 or FE-300, which is perfectly suited to the needs of the circuit. compatible transmitters: TL-300, TL-301, TL-420, TL-421, TL-428, TL-429, TL-432 . Supports extensions: TL-424 / TL-425.
- Page 2 20 cm. deberá utilizar cable apantallado, conectando la malla al terminal correspondiente con el símbolo de masa. ANTENA : Debe instalarse antes de hacer funcionar el telemando, le recomendamos la antena Cebek C-0509 y la C-0510 ó un cable de 130 mm.
- Page 3 TL-423 CONEXIÓN DEL RELÉ. CONTROL DE CARGA : La conexión del relé no debe contemplarse como una salida, no proporciona tensión. Aislado eléctricamente del resto del circuito, su función es abrir o cerrar sus contactos para permitir o interrumpir el paso de una corriente eléctrica, como haría un interruptor sobre una bombilla.
- Page 4 TL-423 INSTALLATION : In a ventilated and away from humidity and high temperature box. PROGRAMMING : The receiver could not be controlled if you have not made a prior programming. Once completed, it will be stored even without power, and is not removed to be replaced by a new programming.
- Page 5 TL-423 INSTALACIÓN : En una caja ventilada y lejos de humedades y de temperaturas altas. PROGRAMACIÓN : El receptor no puede ser controlado si no se ha hecho una programación previa. Emparejamiento con unidad emisora : Cada receptor admite un máximo de 5 emisores por relé del GRUPO 3. El receptor siempre viene de fábrica sin codificar ,y usted tiene que codificarlos para que funcione el emisor y receptor conjuntamente.
- Page 6 TL-423 DIN CONFIGURATION RELAY OUTPUT www.cebek.com sat@fadisel.com...
- Page 7 TL-423 Factory reset : Erases the control and setting, turn off the power 10 seconds with enter button and selec pressed simultaneously, turn on the power. Keep tight, the LED program blinks fast for 5 seconds, stays fixed and then off, the receiver is reset .