WILSON PRO 1000R Guide De L'utilisateur page 16

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Specifi cations
Product Number
Model Number
FCC ID
Connectors
Antenna Impedance
Frequency
Passband Gain (nominal)
20 dB Bandwidth (MHz)
Maximum
Power output for single cell
phone (Uplink) dBm
Power output for single cell
phone (Downlink) dBm
Power output for multiple
received channels (Uplink) dBm
No. Tones
Power output for multiple
received channels
(Downlinklink) dBm
No. Tones
Noise Figure
Isolation
Power Requirements
The term "IC" before the radio certifi cation number only signifi es that Industry Canada technical specifi cations were met.
Each Signal Booster is individually tested and factory set to ensure FCC compliance. The Signal Booster cannot be
adjusted without factory reprogramming or disabling the hardware. The Signal Booster will amplify, but not alter
incoming and outgoing signals in order to increase coverage of authorized frequency bands only. If the Signal Booster
is not in use for fi ve minutes, it will reduce gain until a signal is detected. If a detected signal is too high in a frequency
band, or if the Signal Booster detects an oscillation, the Signal Booster will automatically turn the power off on that
band. For a detected oscillation the Signal Booster will automatically resume normal operation after a minimum of 1
minute. After 5 (fi ve) such automatic restarts, any problematic bands are permanently shut off until the Signal Booster
has been manually restarted by momentarily removing power from the Signal Booster. Noise power, gain, and linearity
are maintained by the Signal Booster's microprocessor.
The Manufacturer's rated output power of this equipment is for single carrier operation. For situations when multiple
carrier signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is re-
radiated and can cause interference to adjacent band users. This power reduction is to be by means of input power or
gain reduction and not by an attenuator at the output of the device.
14
EN
698-716 MHz, 729-746 MHz, 746-756 MHz, 777-787 MHz, 824-894 MHz, 1850-1995 MHz,
700
Band12/17
MHz
57.6
700
Band12/17
MHz
Typical
29.6
35.4
700
Band12/17
MHz
25.3
700
Band12/17
MHz
15.2
700
Band12/17
MHz
2
23.0
3
19.5
4
17.0
5
15.0
6
13.5
700
Band12/17
MHz
2
16.1
3
12.6
4
10.1
5
8.1
6
6.6
IN-BUILDING SIGNAL BOOSTER
460037
460036
PWO460037
N-F emale
50 Ohms
1710-1755/2110-2155 MHz
700
Band13
800
MHz
MHz
58.0
59.2
700
Band13
800
MHz
MHz
30.3
36.8
35.4
37.8
700
Band13
800
MHz
MHz
25.8
24.7
700
Band13
800
MHz
MHz
13.9
15.4
700
Band13
800
MHz
MHz
23.9
20.4
20.4
16.9
17.9
14.4
15.9
12.4
14.4
10.9
700
Band13
800
MHz
MHz
15.2
15.3
11.7
11.8
9.2
9.3
7.2
7.3
5.7
5.8
5 dB nominal
> 90 dB
12V 3A
1700/2100
1900
MHz
MHz
65.7
65.2
1700/2100
1900
MHz
MHz
77.5
74.5
81.0
75.1
1700
1900
MHz
MHz
26.2
25.3
2100
1900
MHz
MHz
15.4
15.4
1700
1900
MHz
MHz
22.4
22.1
18.9
18.6
16.4
16.1
14.4
14.1
12.9
12.6
2100
1900
MHz
MHz
12.0
15.3
8.5
11.8
6.0
9.3
4.0
7.3
2.5
5.8
WILSON PRO 1000R

Publicité

Table des Matières
loading

Produits Connexes pour WILSON PRO 1000R

Ce manuel est également adapté pour:

460037460036

Table des Matières