AquaScape 84074 Instructions D'installation

I N S T A L L A T I O N
SMART CONTROL HUB
FOR COLOR-CHANGING LIGHTS
Contents - #84074
No. Description
1. Smart Control Hub for color-changing lights
For complete light installation steps and warranty
information, please see the LED Color-Changing
Lights instruction manual.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference, and
2. this device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
Required
• Adequate WiFi coverage reaching to the unit (2.4 GHz networks
supported)
• Aquascape Smart Control App (available on iOS or Android App Store)
Installation
• The Aquascape Smart Control Hub is required to power and control
Aquascape color-changing lights.
• Securely attach included antenna to the top of the Hub (Ex. 1).
• Connect the light, splitter, or extension to the 5-pin quick-connect fitting
attached to the hub (Ex. 2).
NOTE: Each Smart Control Hub can control up to 150-watts of color-
changing lights.
NOTE: Multiple Smart Control Hubs can be used to assign multiple
colors simultaneously.
facebook.com/aquascapeinc
youtube.com/aquascape4
pinterest.com/aquascapeinc
I N S T R U C T I O N S
NOTE: The Smart Control Hub is weather resistant, but not waterproof.
Install it off the ground and protected from the elements.
TRANSFORMER SETUP
• Aquascape color-changing lights are designed to operate on a 12-volt,
outdoor-rated transformer.
1
NOTE: It is recommended to locate the transformer as close to the light
fixtures as possible to avoid voltage drops caused by long cable runs.
• Plug the transformer into a GFCI-protected outlet.
5
PAIRING PROCEDURE
• Plug the Smart Control Hub into a12-volt transformer, and the unit will
automatically enter pairing mode.
NOTE: The blinking blue light on the face of the unit indicates the plug is
in pairing mode and ready to be connected.
• Download the Aquascape Smart Control App (available on iOS or
Android App Store).
• Open the Aquascape Smart Control App and
click 'Create New Account' (Ex. 3).
NOTE: If you already have an account, login with
your username and password.
• Once logged in, click the three dashes in the
upper, right-hand corner of the home screen
(Ex. 4).
• Click 'Add New Device' (Ex. 5).
NOTE: Adequate WiFi coverage is required
(2.4 GHz networks supported)
• Continue to follow on-screen instructions to
complete the pairing process.
• To reset the device to factory
defaults, press and hold the pairing
button for ten seconds and release
when the light begins rapidly
flashing (Ex. 6).
Troubleshooting
• Device won't pair
– Make sure the outlet is receiving power
– Make sure you have adequate wireless coverage to connect the
device (2.4 GHz networks supported)
– Reset the device to factory defaults
– Make sure the ground-fault circuit interrupter (GFCI) is not tripped
– Reset your wireless router
Ex. 1
Ex. 5
For more information about our company or products, please visit our website at
aquascapeinc.com or call us at US (866) 877-6637 CAN (866) 766-3426
©2020 Aquascape, Inc. • All Worldwide Rights Reserved
Ex. 2
Ex. 3
Ex. 4
Ex. 6
10/20