Publicité
English
CONTROLS / POWER SUPPLY
CONTROLS ( see figure 1 )
1 OPEN 2 ..............opens the CD lid
2 DBB.....................switches the bass enhancement on and off. This button also
switches acoustic feedback (the beep) on/off when it is
pressed for more than 2 seconds
3 MODE .................selects the different playing possibilities: shuffle,
shuffle repeat all, repeat, repeat all and SCAN
4 PROG...................programs CD tracks and radio stations, reviews the program
5 PRESET 3 ,4 .....selects a preset tuner station (down, up)
6 FM.......................switches the radio on or off.
7 ............................display
8 2;, 9 .................- switches the player on, starts or pauses CD play
- stops CD play, clears a program or switches the player off
9 TUNING ∞ , §
TUNER : - (down,up) tunes to radio station;
CD : - skips and searches CD tracks backwards or forwards.
0 RESUME .............stores the last position of a CD track played
HOLD...................locks all buttons
OFF......................switches RESUME and HOLD off
! LINE OUT/p........3.5 mm headphone socket and LINE OUT socket to connect
the player to another audio input of an additional appliance.
@ VOL E ............adjusts the volume
# 4.5V DC...............socket for external power supply
$ ............................belt clip holder
% ............................type plate
Batteries (supplied or optionally available)
You can use the following batteries with this CD-player:
• normal batteries type LR6, UM3 or AA (preferably Philips), or
• alkaline batteries type LR6, UM3 or AA (preferably Philips).
Notes:– Old and new or different types of batteries should not be combined.
– Remove batteries if they are empty or if the player is not going to be used for
a long time.
Inserting batteries
1 Push OPEN 2 to open the CD lid.
2 Open the battery compartment and insert either 2
normal or alkaline batteries, or the rechargeable
NiMH battery AY3362 (if supplied).
Battery indication
The approximate power level of your batteries is shown in the display.
Battery full
Battery two-thirds full
Battery one-third full
Battery dead or empty. When the batteries are
dead or empty, the symbol
bAtt is displayed, and the beep tone sounds repeatedly.
Average playing time of batteries under normal conditions
Battery type
Normal
Alkaline
Rechargeable ECO-PLUS NiMH battery
Batteries contain chemical substances, so they should be disposed
of properly.
flashes,
ESP on
Power Save
5 hours
6 hours
16 hours
20 hours
7 hours
9 hours
POWER SUPPLY / GENERAL INFORMATION
ECO-PLUS NiMH battery information (for versions supplied with the
rechargeable ECO-PLUS NiMH battery AY 3362)
Recharging works only on players supplied with the rechargeable ECO-PLUS
NiMH battery AY 3362.
Recharging the ECO-PLUS NiMH battery on board
1 Insert the rechargeable ECO-PLUS NiMH battery AY 3362.
2 Connect the mains adapter to the 4.5V DC socket of
the player and then to the wall socket.
y
is pulsing.
• Recharging stops after a maximum of 7 hours, or
when you start playback.
3 When the battery is fully recharged,
FULL appear briefly in the display,
Notes: – It is normal for the batteries to become warm during recharging.
– If the batteries become too warm, recharging will be interrupted for
approximately 30 minutes and Hot is displayed.
– To ensure proper recharging on board, take care that contacts are
clean.
– Use only the ECO-PLUS NiMH battery AY 3362.
Handling instructions
• Recharging already charged or half-charged batteries will shorten their
lifetime. We therefore recommend that you let the rechargeable ECO-PLUS
NiMH battery run till it is completely empty before you recharge it.
• To avoid a short circuit, do not let the battery touch any metal object.
• If the battery becomes empty soon after recharging, then either its contacts
are dirty or it has reached the end of its lifetime.
Mains adapter (supplied or optionally available)
Use only the AYT 3170 adapter (4.5 V / 300 mA direct
current, positive pole to the center pin). Any other product
may damage the player.
1 Make sure the local voltage corresponds to the
power adapter's voltage.
2 Connect the power adapter to the 4.5V DC socket of
the player and to the wall socket.
Note: Always disconnect the adapter when you are not using it.
Belt Clip (not on all versions)
1 To attach the belt clip to the CD-player, position the
shaped grip (found on the back of the belt clip) so
that it fits into the belt clip hole of the CD-player.
2 Turn the clip to LOCK as indicated on the set.
3 To detach, gently lift the belt clip and turn
to RELEASE as indicated on the set.
Environmental information
• All redundant packing material has been omitted. We have done our utmost to
make the packaging easily separable into two materials: cardboard (box) and
polyethylene (bags, protective foam sheet).
• Your set consists of materials which can be recycled if disassembled by a
specialized company. Please observe the local regulations regarding the
disposal of packing materials, dead batteries and old equipment.
and
BELT CLIP
LOCK
LIFT
RELEASE
Publicité
