Garrison 046-7228-0 Instructions D'installation

®
INSTRUCTIONS FOR INSTALLATION
OF TUBULAR LOCKSET
For use on doors 1 3/8" to 1 3/4" (35 mm-45 mm) think
model no.: 046-7228-0 & 046-7229-8 & 046-7230-2 & 046-7847-6 & 046-7852-2 & 046-7849-2 &
046-5694-0 & 046-5695-8 & 046-5696-6 & 046-2470-0 & 046-2478-4 & 046-2479-2 &
046-2002-6 & 046-2610-8 & 046-2611-6
Toll-free Number: 1-800-268-6591
IMPORTANT
: Please read this manual carefully
before installing this deadbolt lock and save it for reference.
Adjustable latch for 2 3/8" (60 mm) and 2 3/4" (70 mm) backset
Backset is a distance from door edge to centr of
hole on door face.
Some locks are supplied with adjustable latch which
can fit 2 3/8" (60 mm) or 2 3/4" (70 mm) backset.
Follow the steps shown below to change backset.
Before Proceeding :
The distance of backset which is from the edge of the door to the center of
lock, either 2 3/8" (60 mm) or 2 3/4" (70 mm). Your latch was preset at the
factory for 2 3/8" (60 mm) backset.
If a 2 3/4" (70 mm) backset is required, follow the adjustment instructions
in step 1a.
1a 1b
If 2 3/4" (70 mm) backset is required, Be sure the stem hole of
pull spindle cam all the way to the upper/lower cam is properly
right end of the adjusting hole. aligned.
1c 1d
Your latch is now set at 2 3/4" (70 mm) To reset the latch to 2 3/8" (60 mm)
backset. backset, push spindle cam to the
left end of the adjusting hole.
Latch Face Plate
Determine which latch mounting method will be
used and made necessary adjustments.
No adjustment required for square latch face plate.
To change latch face :
1. Use a flat screwdriver to separate the face plate.
2. Snap selected face plate onto back plate.
Drive-in faceplate installation
Remove original faceplate.
Align the round faceplate with the latch bolt and
push it inside the latch bolt until you hear the catch click.
All manuals and user guides at all-guides.com
1. Mark the door with template
2. Drill holes
3. Install latch
a
e
a. Insert latch in hole and keep it
parallel to door face.
Mark outline of face plate and
remove latch.
c
c. Insert latch and tighten screw.
Right Wrong
Select 2 3/8" or 2 3/4" (60 mm or 70 mm) backset as
desired and mark centre of hole on door face.
a. Drill 2" (51 mm) hole through door face, from both
sides to avoid wood splitting.
b. Drill 1" (25.4 mm) hole for latch
(refer to step 3d for drive-in latch).
b
b. Chisel 5/32" (4 mm) deep inside
traced outline or until face plate
is flush with door edge.
d
d. For drive in latch, drill 1"
(25.4 mm) hole and press latch
until it is flush with door edge.
Fold on dotted line and fit on door edge
45 40 35
1 3/4" 1 9/16" 1 3/8"
Mark 1" (25.4mm) hole at center of door edge.
4. Install strike
a. Close the door so the latchbolt is against the door
a
frame.
b. Measure one half of door thickness from door stop
b
and vertically mark center line of strike.
Drill 1" (25.4 mm) hole, 1" (25.4 mm) deep at
intersection of horizontal and vertical line of strike.
Mark outline using strike plate and chisel
1/6" (1.6 mm) deep for strike.
c. Install strike and tighten screws.
c
5. Install outside knob
Insert spindle through latch.
Press flush against door.
Note: Key hole must be in down position.
6. Install inside knob
Install inside knob and tighten screws until lock
is firm.
For 2 3/4" (70 mm) backset
For 2 3/8" (60 mm) backset
7/32" (5.5 mm)
x2 hole
2 1/4" (57 mm)
for metal door only.
ø 2 1/8" 54 mm ( )
G-TA-01