Battery Insertion/Replacement - monzana DBFU001 Mode D'emploi

INSTRUCTIONS
Only for domestic use and not for commercial use.
ATTENTION! Observe the safety and assembly
instructions in order to avoid the risk of injury or
damaging the product.
Important: Read these instructions carefully
and thoroughly. Keep these instructions to read
through at a later date. If you give the product to
anyone else at some point in the future, please
ensure you also pass on this manual.
Keep small parts out of the reach of children.
Pay attention especially when unpacking it. Keep
plastic bags and other packaging away from
children reach. Danger of Suffocation!
Check all elements and parts for damages.
Despite careful checks since may happen that
even the best product takes damage during the
transport.
In this case, do not build up of your product.
Defective parts can endanger your health.
Never modify the product! Changes will void the
warranty and the product may be unsafe or even
dangerous.
For cleaning use a sponge and warm soapy water.
Do not use solvent based-cleaners or detergents
for example Bleach those can damage the
product.
4
2
3
5
1. BATTERY
2. RESET
3. M. SET
4. REC
5. TRANSPORT SAFETY
Before you take the clock in operation, remove
the transport safety (5).

BATTERY INSERTION/REPLACEMENT

To install and replace the battery, please follow
these steps.
1. 1.Pull down the battery (1) compartment (at
the back of the case).
2. Insert a new battery (AA type, 1.5V, LR6) ,
observing correct polarity as indicated in the
battery compartment.
3. Put lid (1) back again.
www.Deuba24online.de
SETTING THE MOVEMENT AUTOMATICALLY
• Once the battery is installed properly. the
movement (clock) automatically sets itself to
12 O'clock and then receiving the signal,i.e. The
second hand moves to 0 position follow by the
hour and minute hand move to 12:00 position.
• When the hour hand,minute hand and the
second move to 12:00 position, it starts to
receive the radio signal. Once it has received the
radio signal and processed it accordingly (which
takes 3 to maximum 12 minutes), the move-
ment (clock) automatically displays the correct
time. We recommend that you do not put up
or hang up the movement/clock) automatically
displays the correct time. We recommend that
you do not put up or hang up the movement/
clock anywhere during this process.
1
• It the movement (clock) still has not set itself
after 12 minutes, reception is faulty or not
possible at the chosen location. Repeat setting
at a different location by pressing the RESET 2
button.
TO SET THE TIME MANUALLY
• Press and hold the M. SET 3 button for 3
seconds to set the time.
• Press the M. SET 3 button for 1 second to
advance 1 minute.
• Press the M. SET 3 button for more than 1
second to auto advance the minute hand.
• If the M. SET 3 button is not pressed for 8
seconds, the movement (clock) is set.
4 5 w w w.De ub a 2 4 onl i ne .d e
RESET THE MOVEMENT (CLOCK)
• Press the RESET 2 button will reset the
movement (clock) data.
• The hour hand,minute hand and the second
hand move to 12:00 position.
• When the hour hand,minute hand and the
second move to 12:00 position, it starts to
receive the radio signal.
FORCE RADIO SIGNAL RECEPTION
• During normal operation, press the REC 4
button for 3 seconds will force to receive the
radio signal.
• The hour hand, minute hand and the second
hand move to 12:00 position.
• When the hour hand,minute hand and the
second hand move to 12:00 position, it starts to
receive the radio signal for 3-12 minutes.
• Once it has received the radio signal,and
processed it accordingly. the movement (clock)
automatically displays the correct time.
• If the time still has not set itself after 12
minutes, reception is faulty and it will resume
the time before the force reception.
RECEIVING THE RADIO CONTROL SIGNAL
The radio-controlled movement (clock) will
automatically receive the radio signal 12 times
every day (i.e.1:00,3:00,5:00...,19:00,21:00,23:0
0) It will take 3-12 minutes to receive the radio
signal.
This item complies with all the required European
standards.