Table des Matières
Publicité
co
Please
read these
instructions carefully before you start to
assemble this
product
and carry
out the
steps
in
the order
set
out
in
these
instructions.
When
encountering the information
icon, please refer to the relevant
assembly step for additional comments and
assistance.
Care
and Safety Advice
For
safety purposes we
strongly recommend the product to
be
assembled
by at least
two
people.
Some parts may have
sharp edges.
Please be
careful when handling components.
Always wear gloves, eye
protection, and long
sleeves
when assembling or performing
any
maintenance on your product.
Do
not attempt to
assemble the
product
in
windy
or wet conditions.
Dispose
of
all
plastic
bags safely
-
keep
them out of
reach
of
small
children.
Keep
children away from the assembly
area.
Do
not attempt to
assemble the
product if you
are
tired,
have
taken drugs,
medications or alcohol, or if you
are
prone to dizzy
spells.
When using
a
stepladder or power tools, make
sure
you
follow
the manufacturer's
safety advice.
Do
not climb or
stand on
the
roof.
Heavy
articles should not
be
leaned against
the
poles.
Do
not
hang or
lay on
the profiles.
Keep
roof and gutter clear of
snow,
dirt
& leaves.
Heavy
snow load on roof
can
damage the product making it unsafe to stand
below or
nearby.
Keep
these
instructions
in
a
safe
place
for future
reference.
If
color
was
scratched
during
assembly it
can be
fixed with the
following
tints:
White
-
RAL
9016
Cleaning Instructions
When
your product
needs
cleaning,
use
a
mild detergent solution and
rinse
with cold
clean water.
Do
not
use
acetone, abrasive cleaners, or others special detergents to clean the panels.
Before Assembly
This
product
must
be
assembled on
a
solid, level
base
/
surface (such
as
concrete or
asphalt) and anchored to the ground.
Choose
your
site
carefully before beginning
assembly.
Sort
the
parts and check according to the contents parts
list.
Please
consult your
local
authorities if
any permits
are
required prior to constructing
the product.
Tools &
Equipment
T001
(Supplied)
Notes
During Assembly
When
encountering
these icons, you
are
requested to either keep the
screws
slightly
loose
or to fully tighten the
screws.
Lil
J ceps
Step 8:
Please
apply silicone
sealants above beam
7288
+
7289,
in
order to prevent water from
seeping
in
(drawing
b).
Step 12:
Please
note the profile's direction (8063), the
canal
should
be
on
the external
side.
Step 13: Make sure that the angle between the back wall profile and the panel supporting profiles
is
90
degrees. Make
sure
you place the profiles according to the measurements given.
Step 20:
Please
install the panels
as
shown
in
the drawings, starting from the middle to the
sides
right then left alternately.
Step 23:
Please
apply silicone
sealants
to the inner edges of parts 7033 & 7032
as
well
as
to the
middle of parts 8119
+
7039
in
order to prevent water from seeping
in.
Step 24
a
+
b:
Please
apply silicone sealant on the inner part of 8116 & 8117
(a)
and connect to the
profile (b).
Step 24
c:
Adjust the gutter
head's
angle according to
your
needs and
tighten screw 4043 from the
inside.
* It
is
possible to connect standard drainage pipes
(2.07" diameter)
to the
gutter
heads'exit.
Step 28: Important!
Please
make
sure
the frame
is
perfectly centered before fixing.
Step 31:
Please
do not cut profile 8055
unless needed.
Step 33:
Please
loosen the screws
as
shown
in
diagram
c,
set
the beam exactly on
top of
the
poles,
once done re-tighten the
screws.
Step 34:
Please
loosen the screws, and remove
the end
poles (8063)
as
shown, they will
be re-set later.
Step 40:
Important!
Do
not over
tighten
the
screws.
Use
compatible
screws
and masonry anchors for
your type of
base
/
foundation.
Step 41:
Please
do not cut profile 8056
unless needed.
Step 42:
Please
do not cut profile 8057
unless needed.
Please
do not cut the Acrylic sheets 8111 & 8113
unless needed, all
precautions must
be
taken.
Step 46: Install the sealing strip on the
outer
side
as
shown
in
the diagram.
Step 51:
Note the doors'corners should
be
at
a
90°
angle. Should you have
difficulties
in
manipulating
the doors, tap on the door's corner
with
a
rubber mallet.
(Do
not tap directly on the corner,
use
a
small
wooden
plank)
Step 55:
Please
note!
The
master
key
attached to the doors,
locks
from the inside.
Step 56: Optional! Part
8531
sets
the grey marked doors, thus creating smaller openings.
*Tighten
all screws
when completing assembly.
Please
note:
Anchoring this product to the ground
is
essential to
its
stability
and rigidity, and required
in
order for your warranty to
be
valid.
The
wall anchoring kit supplied
with
this product
is
suitable only for concrete
walls.
Other wall types need
an
accordant wall fixation
kit.
Publicité
Table des Matières
