Emerson White-Rodgers 24A06G-1 Instructions D'installation

Operator: Save these instructions for future use! Operator: Save these instructions for future use! Operator: Save these instructions for future use! Operator: Save these instructions for future use! Operator: Save these instructions for future use!
FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE
FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE
INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL
INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL
INJURY AND/OR PROPERTY DAMAGE. INJURY AND/OR PROPERTY DAMAGE. INJURY AND/OR PROPERTY DAMAGE. INJURY AND/OR PROPERTY DAMAGE. INJURY AND/OR PROPERTY DAMAGE.
This Dual Level-Temp Silent Operator Relay is designed for
controlling two separate loads with a single low voltage
thermostat. It is especially suitable for use with electric heating
equipment.
The Dual Level-Temp relay may be used to operate two
separate heating loads by means of a single low voltage
thermostat. It is equally well suited for use with a heating-
cooling thermostat to control heating and cooling loads alter-
nately as in motels, apartments, office buildings, etc.
This model Dual Level-Temp relay has a voltage input of 240
volts. Since this relay is equipped with a self-contained trans-
former, the supply voltage used must agree with the voltage
rating of the relay. This model has both an inductive and non-
inductive rating.
If in doubt about whether your wiring is millivolt, line, or low
voltage, have it inspected by a qualified heating and air
conditioning contractor, electrician, or someone familiar with
basic electricity and wiring.
Do not exceed the specification ratings.
All wiring must conform to local and national electrical codes
and ordinances.
This control is a precision instrument, and should be handled
carefully. Rough handling or distorting components could
cause the control to malfunction.
ELECTRICAL DATA ELECTRICAL DATA ELECTRICAL DATA ELECTRICAL DATA ELECTRICAL DATA
Switch Action: Switch Action: Switch Action: Switch Action: Two SPST switches, normally open Switch Action:
Thermal: Thermal: Thermal: Thermal: Thermal: Average time delay – 45 seconds
Ambient Temperature: Ambient Temperature: Ambient Temperature: -20° to 120°F (-24° to 49°C)
Ambient Temperature: Ambient Temperature:
Mounting: Mounting:
Mounting: Mounting: Mounting: 1/2" conduit hub or two key slot mounting holes
TYPE
NUMBER VOLTAGE /FREQUENCY
24A06G-1 240VAC, 60 Hz
*FLA - Full Load Amps.; LRA - Locked Rotor Amps.
(Red and Black Leads)
INPUT
NON-INDUCTIVE
25A, 6000W
White-Rodgers is a division
of Emerson Electric Co.
www.white-rodgers.com
24A06G-1 24A06G-1
24A06G-1 24A06G-1 24A06G-1
DUAL LEVEL-TEMP
SILENT OPERATOR RELAY
(Normally Open Contacts)
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS
The Silent Operator relay has been carefully adjusted at the
factory, and no attempt should be made to adjust them in the
field.
To prevent electrical shock and/or equipment damage, To prevent electrical shock and/or equipment damage, To prevent electrical shock and/or equipment damage, To prevent electrical shock and/or equipment damage, To prevent electrical shock and/or equipment damage,
disconnect electric power to system at main fuse or disconnect electric power to system at main fuse or disconnect electric power to system at main fuse or
disconnect electric power to system at main fuse or disconnect electric power to system at main fuse or
circuit breaker box until installation is complete. circuit breaker box until installation is complete.
circuit breaker box until installation is complete. circuit breaker box until installation is complete. circuit breaker box until installation is complete.
Do not use on circuits exceeding specified voltage. Do not use on circuits exceeding specified voltage. Do not use on circuits exceeding specified voltage.
Do not use on circuits exceeding specified voltage. Do not use on circuits exceeding specified voltage.
Higher voltage will damage control and could cause Higher voltage will damage control and could cause
Higher voltage will damage control and could cause Higher voltage will damage control and could cause Higher voltage will damage control and could cause
shock or fire hazard. shock or fire hazard. shock or fire hazard. shock or fire hazard. shock or fire hazard.
Thermostat Circuit Current: Thermostat Circuit Current: Thermostat Circuit Current:
Thermostat Circuit Current: Thermostat Circuit Current:
Bimetal Heater #1 (Red & White Leads) Bimetal Heater #1 (Red & White Leads)
Bimetal Heater #1 (Red & White Leads) Bimetal Heater #1 (Red & White Leads) Bimetal Heater #1 (Red & White Leads) – 0.21 Amps
Bimetal Heater #2 (Red & Black with White Stripe Bimetal Heater #2 (Red & Black with White Stripe Bimetal Heater #2 (Red & Black with White Stripe Bimetal Heater #2 (Red & Black with White Stripe Bimetal Heater #2 (Red & Black with White Stripe
Leads) Leads) Leads) Leads) Leads) – 0.21 Amps
ELECTRICAL RATING
FOR SWITCH #1
INDUCTIVE*
12 FLA (72 LRA)
DESCRIPTION DESCRIPTION DESCRIPTION
DESCRIPTION DESCRIPTION
PRECAUTIONS PRECAUTIONS
PRECAUTIONS PRECAUTIONS PRECAUTIONS
CAUTION
!
WARNING
!
SPECIFICATIONS SPECIFICATIONS
SPECIFICATIONS SPECIFICATIONS SPECIFICATIONS
FOR SWITCH #2
(Red Striped and Black Striped Leads)
NON-INDUCTIVE INDUCTIVE*
25A, 6000W 12 FLA (72 LRA)
PART NO. 37-4165C PART NO. 37-4165C PART NO. 37-4165C
PART NO. 37-4165C PART NO. 37-4165C
Replaces 37-4165B
0504