Homestyles 73005131 Manuel Du Propriétaire
Masquer les pouces
Voir aussi pour 73005131:
- Manuel du propriétaire (40 pages) ,
- Manuel du propriétaire (12 pages)
Table des Matières
Publicité
Liens rapides
High Windload Kit - Wall Asm
PLEASE READ ASSEMBLY INSTRUCTIONS COMPLETELY BEFORE STARTING
PLEASE READ OWNER'S MANUAL
COMPLETELY BEFORE ASSEMBLING
YOUR SHED.
ALL STATED SIZES ARE NOMINAL DIMENSIONS.
All manuals and user guides at all-guides.com
PROPRIÉTAIRE EN ENTIER AVANT
D'ASSEMBLER LA REMISE.
TOUTES LES DIMENSIONS INDIQUÉES SONT NOMINALES.
Models / Modèles / Modelos
10x8
Owner's Manual
Manuel du propriétaire
Manual del Propietario
Version / Edición
1.0
POR FAVOR, LEA COMPLETAMENTE
EL MANUAL DEL PROPIETARIO ANTES
DE ENSAMBLAR LA EDIFICACIÓN.
TODAS LAS DIMENSIONES INDICADAS SON NOMINALES.
73005131
73005132
73005105
Publicité
Table des Matières
Manuels Connexes pour Homestyles 73005131
Sommaire des Matières pour Homestyles 73005131
- Page 1 All manuals and user guides at all-guides.com Models / Modèles / Modelos 10x8 73005131 73005132 73005105 Owner’s Manual Manuel du propriétaire Manual del Propietario Version / Edición High Windload Kit - Wall Asm PLEASE READ ASSEMBLY INSTRUCTIONS COMPLETELY BEFORE STARTING PLEASE READ OWNER’S MANUAL...
- Page 2 All manuals and user guides at all-guides.com PLEASE TAKE A COMPLETE INVENTORY OF ALL PARTS USING THE PARTS LIST AND PART IDENTIFICATION GUIDE PROVIDED ON PAGES 5 AND 7. DO NOT ATTEMPT TO ASSEMBLE BUILDING IF PARTS ARE MISSING OR DAMAGED. DO NOT RETURN PRODUCT TO STORE. IF YOU NEED REPLACEMENT PARTS PLEASE CALL 1-877-362-3409.
-
Page 3: Part Identification
All manuals and user guides at all-guides.com Part Identification WL Door Jamb Brace Base Track Corner Post (AL1-AL4) (CN1) Wall Support Beams Back/Side Wall Panel Front Wall Panel (WSB) (WP1/WP2) (WP3) Door Lintel Wall Cap (LT1/LT2) (SC1) • #10 x 3/4" •... -
Page 4: Matériaux Nécessaires
All manuals and user guides at all-guides.com IMPORTANT NOTE ON CONDENSATION! REMARQUE IMPORTANTE SUR LA CONDENSATION ¡NOTA IMPORTANTE SOBRE LA CONDENSACIÓN! All buildings are subject to condensation. Some of the Tous les immeubles peuvent subir de la condensation causée par En todo edificio ocurre el fenómeno de la condensación. - Page 5 All manuals and user guides at all-guides.com Identify your Base Track configuration using the diagrams below. Install the base track sections on your foundation using Hilti Kwik 3/8” x 5” bolt (WLB) screws (WLB). Please note: The diagonal measurement included in the diagram may vary slightly from the actual measurement. It is important to ensure that your track has been squared o and your door opening is 71 "...
- Page 6 All manuals and user guides at all-guides.com Insert Wall Support Beams (WSB) into walls during assembly and mark the location of the Wall Support Beams on the inteior of the shed walls with a pen for reference. Insert a Corner Post (CN1) and a Back and Side Wall Panel (WP1/WP2) at the rear of the platform.
- Page 7 All manuals and user guides at all-guides.com Insert Wall Support Beams (WSB) into walls as shown and mark the location of the Wall Support Beams on the inteior of the shed walls with a pen for reference. Add the remaining WP2 panels to build the right side wall. Ensure all parts are fully seated.
- Page 8 All manuals and user guides at all-guides.com Add the Wall Caps (SC1) to the side walls as shown. The front and rear edges of the wall cap should be flush (no overhang) with the front and rear edge of the side wall panels to ensure proper seating of the gables at Step 9. I mage shown is for 10x10. Posez les couvre-joints muraux (SC1) sur les murs latéraux.
-
Page 9: Important
All manuals and user guides at all-guides.com IMPORTANT: For the next two steps, be sure to check door alignment several times during screw installation to ensure building h as not moved out of alignment. If it has, realign and resume installation of screws. IMPORTANT: Pour les deux prochaines étapes, véri ez l’alignement des portes à... - Page 10 All manuals and user guides at all-guides.com 30-1 From inside of shed, locate the Wall Support Beam marks made from steps 3-6. Pre-drill using 9/64 drill bit at the wall cap interface and Floor Track Self Tapping screws (ST1) Wall Support Beams (WSB) Line up screws with marks made Steps 3 thru 6 to ensure contact to Wall Support Beams (WSB) Wall Support Beams (WSB) •...