Thomas & Betts Ty-Rap TC5342A-NDT Instructions D'installation

2-Way Mounting Base
Socle de xation à 2 voies
Base de montaje de 2 vías
Cat. No.
Cat. N°
TC5342A-NDT
TC3421-NDT
Figure
3 TC5342A-PDT Polypropylene
Figura
TC342A-PDT
4-Way Mounting Base
Socle de xation à 4 voies
Base de montaje de 4 vías
Figure
4
Figura
Material Optional Mounting Screw
Cat. No.
Matériau Vis de fixation en option
Cat. N°
Material Tornillo de montaje opcional
TC5344A-NDT
Nylon
TC344A-NDT M3/#5 Pan Head Screw
Vis à tête tronconique M3/N° 5
TC5344A-PDT Polypropylene
M3/#5 Tornillo de cabeza plana
Polypropylène
TC344A-PDT
Polipropileno
4-Way Mounting Base
Base de xation à 4 voies
Base de montaje de 4 vías
Figure
5
Figura
Material Optional Mounting Screw
Cat. No.
Matériau Vis de fixation en option
Cat. N°
Material Tornillo de montaje opcional
TC5347A-NDT
Nylon
TC347A-NDT M4/#8 Pan Head Screw
Vis à tête tronconique M4/N° 8
TC5347A-PDT Polypropylene
M4/#8 Tornillo de cabeza plana
Polypropylène
TC347A-PDT
Polipropileno
*
Maximum Mechanical strength is equivalent to the adhesive bonding strength.
*
La résistance mécanique maximale est équivalente à la résistance de xation par collage.
*
La máxima resistencia mecánica es equivalente a la resistencia de la unión adhesiva.
WARRANTY / GARANTIE / GARANTÍA
• Limited Warranty Applies. Refer to: www.tnb.com/ecpwarranty for full warranty terms.
• Une garantie limitée s'applique. Consultez la page: www.tnb.com/ecpwarranty pour les
conditions complètes de la garantie.
• Se aplica una garantía limitada. Consulte todos los términos de la garantía en
www.tnb.com/ecpwarranty.
Thomas & Betts Corporation
Memphis, Tennessee
TA04709 A Page 4 of 4
www.tnb.com
Page 4 de 4 / Página 4 de 4
A
29 mm
1.125"
6 mm
29 mm
0.250"
1.125"
Material Maximum * Mech. Strength
Matériau Résistance mécanique maximale *
Material Máxima * resistencia mecánica
Nylon
*
133 N / 30 lbs
Polypropylène
Polipropileno
A
19 mm
0.750"
19 mm 5 mm
0.750" 0.190"
Maximum * Mech. Strength
Résistance mécanique maximale *
Máxima * resistencia mecánica
*
44 N / 10 lbs
A
29 mm
29 mm
9 mm
1.125"
1.125"
0.340"
Maximum * Mech. Strength
Résistance mécanique maximale *
Máxima * resistencia mecánica
*
133 N / 30 lbs
© 2014 Thomas & Betts.
All Rights Reserved.
Tous droits réservés.
Todos los derechos reservados.
A
for Detectable Cable Tie Adhesive Backed Mounting Bases
4.8 mm
0.190" IF USING AROUND ELECTRICAL EQUIPMENT DISCONNECT POWER
BEFORE INSTALLING.
DUE TO VARIATIONS IN DETECTION EQUIPMENT AND DIFFERENT DENSITY LEVELS
OF PROCESSED PRODUCT, VERIFY DETECTIBILITY BEFORE USING THIS PRODUCT.
NOTE: THIS PRODUCT IS TO BE INSTALLED BY A QUALIFIED ELECTRICIAN.
COMPLIES WITH:
• FDA Applicable Provisions of Regulation 21CFR
A
• EN 62275, IEC 62275 AND NMX-J-623-ANCE TYPE 2
SHELF LIFE AND STORAGE:
3.5 mm • Adhesive base should be attached to a surface within one year of manufacture, see expiration date on
0.140"
package. Store in a cool dry location below 24°C / 76°F.
INSTRUCTIONS:
1. Apply to mounting surface at 18°C/65°F or above.
2. Clean and dry surface before applying. Be sure surface is free from oil, powder, dust or release agents.
NOTE: This product is approved for mounting to the following surfaces: Stainless Steel, ABS, Nylon, PVC,
Polypropylene, Aluminum, Enameled Painted Steel, and Galvanized Steel.
3. Remove release liner from adhesive pad.
4. Position into desired location and apply rm pressure for 30 seconds.
5. To bundle wires, place appropriate size cable tie length half way through the slot of the mounting base
(Figure 1). Reference maximum cable tie width (Dimension A) shown in the gures 3, 4 and 5.
A
6. Bundle wires uniformly and center over the mounting base (Figure 2).
7. Wrap cable tie around wire bundle and insert tail into tie head.
8. Cinch up cable tie around wire bundle and cut off excess tail.
7.6 mm
0.300"
Half of Cable Tie
into Slot
1
Figure
INSTALLATION INSTRUCTIONS
WARNING
CAUTION
Cable Tie
Wires Bundle
2
Figure
Slots
TA04709 A Page 1 of 4 / Page 1 de 4 / Página 1 de 4
English
FDA
COMPLIANT
MATERIAL
Mounting Base