Trilite SG30-RG Instructions D'installation

IMPORTANT SAFETY INFORMATION
CAUTION! The individual user should determine prior to use whether this device is suitable, adequate,
or safe for the use intended. Since individual applications are subject to great variation, the manufacturer
makes no representation or warranty as to the fit or suitability of these devices for any specific application.
CAUTION! Ensure that the power supply matches the voltage rating of the light.
CAUTION! All units are equipped with an integrated flasher device. Units with incandescent lamps are
required to flash and need this device to prevent heat damage to the lens. LED units can operate safely
when not flashing.
CAUTION! Units with LED lamps require careful control of the DC input voltages if generated from AC
power sources. Ensure that voltage does not exceed 110% of rated voltage.
INSTALLATION INSTRUCTIONS
The Model SG30 consists of two light units; the SG20 which operates as the control unit with an internal flasher circuit and switch,
and the SG10, a drone unit not equipped with a flasher or switch. A six-foot communication cable is supplied to couple the two units
1. If installing units on a loading dock, choose an inside location for the SG20 (control unit) and an outside location for the SG10
(drone unit) that is clearly visible to a driver when backing into the dock bay. The power connection can be through the underside
of the housing or through the back plate. Use the ½" EMT fittings provided.
2. Determine the route for the communication cable between the two units.
3. Using the housing as a template, mark and drill four (4) corner holes. Hardware will depend upon the construction of the wall and
is not included. If mounting to brick or masonry, size the holes to accept ¼" diameter lag-type fasteners and anchors.
Use the back plate gasket provided when mounting unit to the wall.
4. Follow the wiring diagram provided to connect the two units. Do not modify the wiring inside either unit. Store any excess cable
inside the drone unit.
REPLACEMENT PARTS LIST
Part# Descriptions
A1612R Red signal assembly, 12 VDC
A1612G Green signal assembly, 12 VDC
A1624RH Red signal assembly, 24 VAC/VDC
A1624GH Green signal assembly, 24 VAC/VDC
A16115R Red signal assembly, 120 VAC
A16115G Green signal assembly, 120 VAC
403005 On/Off Switch
553031 2-Wire Flasher
LIMITED WARRANTY
This Tri Lite product may incorporate an LED bulb, warranted to be free from defects in materials and/or workmanship for (3) three years from the date of delivery to
Purchaser. The Limited Warranty does not apply to severe applications.
All other components within this unit are under warranty for (1) year. If any component parts do not conform exactly to the specifications and physical dimensions referred
to above, and the Purchaser, at its expense, returns the product or component parts to the Seller together with a report of defects, the Seller shall review the inspection
report and inspect the items and shall authorize, at its option, either the repair or replacement of any non-conforming products or component parts. Upon expiration of
the warranty period, all liability of the Seller shall be terminated.
Seller shall not be liable for any injury, loss or damage, direct or consequential arising out of the use or the ability to use the product. This warranty gives specific legal
rights. You may have other rights, which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so that the
above limitation of exclusion may not apply to you.
info@triliteinc.com | t: 1-773-384-7765 | f: 1-773-384-5115 | www.triliteinc.com | Designers and manufacturers of specialty electrical products. Since 1922.
INSTALLATION INSTRUCTIONS for MODELS
SG30-RG (Incandescent) and SG30-RG-LED
SG30 CONFIGURATIONS
Part# Voltage
SG30-12RG 12v
SG30-12RG-LED 12 VDC
SG30-24RG 24v
SG30-24RG-LED 24v
SG30-115RG 120v
SG30-115RG-LED 120v
.
Amps Bulb Type
4.34 Incandescent
0.60 LED
2.20 Incandescent
0.22 LED
0.42 Incandescent
0.06 LED
953066 | REV B